Also in the mix with all the old reloading tools I inherited is this. It appears to be for removing primers?? As pictured , the 30-40 Krag is too small, & the 45-70 is too big. Any thoughts..
Also in the mix with all the old reloading tools I inherited is this. It appears to be for removing primers?? As pictured , the 30-40 Krag is too small, & the 45-70 is too big. Any thoughts..
You wouldn’t remove them from that direction anyway. A hole puncher for something like a leather belt?
"My main ambition in life is to be on the devil's most wanted list."
Leonard Ravenhill
Less I'm badly mistaken that's a Berdan primer remover tool. Rim seat looks quite large.........you are gonna have to do some diggin there.
I agree, Berdan decapping tool. I use a similar design for 303 British.
The Bird of Time has but a little way
To fly-and Lo! the bird is on the wing
+5 primer remover tool
2nd Amendment of the U.S. Constitution. - "A well regulated Militia, being necessary to the security of a free State, the right of the people to keep and bear Arms, shall not be infringed."
"Before you argue with someone, ask yourself, is that person even mentally mature enough to grasp the concept of different perspectives? Because if not, there’s absolutely no point."
– Amber Veal
"The Highest form of ignorance is when you reject something you don't know anything about".
- Wayne Dyer
I assume it would be a fairly cal. Maybe an old British type??
Measure the opening and compare with the charts in Cartridges of the World. There are probably several cartridge families that would work on with a rim diameter between the .30-40 and .45-70.
Robert
If the pointed ‘punch’ is for depriming the tool would have to be for a short cartridge, otherwise the arm holding the punch would crush the case rim. Even then the arc movement of the punch would be at an extreme angle to enter the case and align with the flash hole. It does look like just to the right of the punch (in the top photo) there is a primer seating anvil that aligns with the scalloped out area of the lower handle.
Maybe the punch and anvil are in the wrong holes. The punch looks like it would deprime if it was in the anvil hole. Do both the punch and anvil fit into both holes in the upper handle?
The punch for pressing in the primer is penned on top , so it is not removable. The spike for removing the primmer can be screwed in & out for the proper setting.
In the first picture there is a little nub behind what is being described as the de-priming pin. Is that nub a primer pocket swager?
A vote for anyone other then the conservative candidates is a vote for the liberal candidates.
Sasquatch-1,
Just guessing here, but I think that is the primer seating pin/ ram. There is a hollow for a case to sit under it.
Robert
Correct. It has a hollow in it. Plus , what would be the primer seater has cup ( picture doesn't show it ) in it that would fit over a primer to seat it in. ingenious old tool. I assume for a very specific cartridge.
On ebay, the seller calls this one a Remington primer remover and replacement tool.
It's probably caliber specific.
In school: We learn lessons, and are given tests.
In life: We are given tests, and learn lessons.
OK People. Enough of this idle chit-chat.
This ain't your Grandma's sewing circle.
EVERYONE!
Back to your oars. The Captain wants to waterski.
Could be for depriming 410 shot shells
Good Shooting
Lindy
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |