Looks like a winner......no problems on the bottom end of the spring either?
Nope, no problemo.
Bullets drops sooo smooth now
A winner for shure
Thanks,
I ended up finding a barely used CR10V3, which has a direct drive extruder, for $350 Canadian ($300USD) and he threw in 2 spools of brand new filament.
I’m in the process of adding Auto Bed Levelling and fixing a couple of minor extruder issues.
Hopefully by tonight or tomorrow it will be ready to start my first 300mm base.
It has been awhile (2+ months...sheesh!), but I finally have something I can show. In mid-February the boards I ordered were printed and delivered. I then ordered the terminal blocks and relay from Amazon. First terminal blocks I ordered had pins that were bigger than the holes in the board and the pitch (pin spacing) was 5.08mm/0.2" instead of the 5mm spacing like the component I selected when designing the board. So those blocks went back and I found ones that would work and got them ordered. All this of course was at the same time the local PO was struggling with deliveries in my area due to carriers being out with Covid. Apparently they have to take a month off if they have it. Deliveries finally got back to normal near the end of February.
After getting the boards, I decided to model a new box with built in standoffs/mounting posts for the relay board and speed controller I use. I also use different connectors for the prox switch, motor and power, so I added cutouts to work with those, and made it so the power came in the bottom of the box and the connectors for the prox switch and motor were on top. I also wanted to be able to mount it to the 3/4" black pipe I that my feeder mounts to, so included the mounts on the box.
Now I have everything soldered to the board, the relay board and speed controller mounted in the box and connected and here is what it all looks like.
These are the connectors I use. I really don't care for those XT connectors for the motor, and trying to solder wire to JST sockets wasn't working for me.
This is the post mount/clamps I put on the box.
I connected it to my feeder and it worked as expected - plate spun when powered and when bullets were detected by the proximity switch it stopped. Need to load test it now just to make sure it doesn't overheat or anything like that.
And for you guys that were talking about the demands of baseball, I can identify. Coached girls basketball and soccer for a number of years. Don't coach any more, but the past weeks we have logged a lot of miles for soccer, which now seems to be a year round sport. The girls I coached from 3rd grade through Jr. High are all graduating this year and its been fantastic to see how much success they have had but it is hard to believe how quickly the time has passed....
It all looks great! You've gone to a lot of effort.....should give you years and years of good service. The best part of 3D printing, is being able to make dang near anything custom to suit us just right. I'm finally done with 5 of them.....happy as can be. Time to clean up my wife says and get serious about reloading again.
My coaching days are long over......all those kids are grown up and married and have their own kids to coach. I'm happy to let them.....but lots of good memories.
New to the site and found this bullet feeder on GitHub. Used the parts generator and have all of the parts printed just need to figure out how it all goes together. Can someone direct me to assembly instructions? Thanks in advance.
I'm working on a fastener application list, but I need some input for motors, other than the ETGZMP38 from Dayton. If there are other fasteners I missed, please let me know and I'll add them.
This is what I have so far:
Attachment 298733
Text Version:
Fastener Application Chart
Brass Chute M2x8 N/A M2 4
Brass Chute Adjuster M3-20 M3 N/A 1
Clutch Hub 6x32x1" Pan Head 6-32 6-32 2 & 4 Nuts
Dillon Mount 3/8"x1" 3/8" Nylock N/A 1
Drop Hole Adapter M2-8 N/A M8 4
Flipper M3-16 N/A M3 1
Flipper Spring Retainer M3-8 N/A N/A 1
Item Fastener Nut Washer Count
Latch Mount M3-8 N/A M3 1
Motor, 634JS
Motor, ETGZMP38 N/A 10-32, Flanged 4
Motor, FC555
Motor, JGY370
Post Mount 3/8"x2" Bolt 3/8" Nut 3/8" 1
Post Mount Angle Adjuster Screw 1/4"-20 1/4"-20 N/A 1
Ramp M3-16 N/A M3 1
Square Post Angle Clamp 3/8"x2" Bolt 3/8" 3/8" 1
Square Post Angle Clamp Adjuster 1/4"-20x21/2" 1/4"-20 1/4" 1
Switch Board M3-20 M3 M3 4
Last edited by wbbh; 04-07-2022 at 03:16 PM.
Sure thing. Here are the various items I used, for anyone that may be interested.
2 pin
https://www.amazon.com/XLX-100PCS-Co...ps%2C76&sr=8-3
3 pin
https://www.amazon.com/RGBZONE-20Pai...ps%2C98&sr=8-3
Power Connectors
https://www.amazon.com/Tegg-Connecto...s%2C109&sr=8-3
Motor Controller
https://www.amazon.com/uniquegoods-1...s%2C136&sr=8-9
Sent from my SM-N981U using Tapatalk
has anyone updated the plate spreadsheet on drop list lately???
The JGY motor uses M3x8 pan head screws... qty 4
I was told that the hex clutch uses #6-32 x 1/2 inch screws and nylock nuts
When i tried to use an M3-20 for the adjustable slide plate to hold the slide in place it is way too short... i think it need at least a 25mm length screw.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |