I don't know if this helps, but it helped me a lot when I was running a factory.
https://content.statefundca.com/safe...Guidelines.asp
I don't know if this helps, but it helped me a lot when I was running a factory.
https://content.statefundca.com/safe...Guidelines.asp
Forgot to mention Home Depot sell a decent hand brand adjustable height work bench.
https://www.homedepot.com/p/Husky-62...DB12/301810799
I generally recommend setting the height of the bench so that the ball/handle is shoulder height. This reduces reaching up or bending to operate the handle. I set my bench for standing height, and use adjustable stool for sitting.
My Feedback, (did I buy or sell to you? Please add your Comments)
http://castboolits.gunloads.com/show...hlight=novalty
I like to stand for some presses/operations and sit for others. Sizing brass and bullets, definitely prefer to stand, leaning on it. Final assembly like to sit and look more closely. As such I like the table to be pretty high. This allows both modes perfectly. Getting the press up makes your neck and eyes relax and if the press is too high to press hard, then stand up which is more ergo for that amount of effort anyway.
Oh so mine is approx kitchen bar height and I’m a tall person. I made it an island though and it has presses on 4 sides
The top of a standard cabinet countertop is 36" above the floor and 24" to the back wall. I would suggest building a workbench to fit whoever will be using it. If you have your press set it on a countertop and lower the press handle all the way down and measure at what height the the press needs to be set to have a comfortable stroke.
I'm 5'11 also and I just rebuilt my bench top. I don't know the exact height but I can post it later. I like to stand and sit on a stool. I built the bench at the best standing height and then cut my stool down to where it felt good to sit at. I used the tall wood stool commonly sold at Sams and such had to take off about six inches.
I would have to check to see my bench height, but I'd reiterate what several other guys have said in that it will depend on your height and how tall your stool is.
Mine is about right for me to stand or sit on a stool, though I find I stand more often than not. I can move around depending on what I'm doing. But I'm either using a single stage press or a Lee Loadmaster (no bullet feeder, I do that on my own), so I tend to reposition fairly frequently.
I elected to go with one the same height as my workbench in the garage. Decided it was better to have it match so if I later want to move it, I won't have benches of two heights.
Thanks everyone for your suggestions!
Good choice …
You can always add a simple wooden riser to raise the press to operate standing.
Here's a pic of a simple wooden box riser made of scrap 2x6/2x8 under my drill press.
You could make it tall enough to clear the press linkage, allowing you to move it back, off the edge of the bench.
Size/Prime a few cases when starting off with a progressive and put them aside. You can plug them back into the process when a bad/odd case screws up in the priming station and continue loading.
Size/Prime a few cases when starting off with a progressive and put them aside. You can plug them back into the process when a bad/odd case screws up in the priming station and continue loading.
Last edited by Kenstone; 01-25-2020 at 03:07 PM.
Size/Prime a few cases when starting off with a progressive and put them aside. You can plug them back into the process when a bad/odd case screws up in the priming station and continue loading.
Nice! Mine is 35.75 inches tall, 24 inches deep, and 31 inches wide. The 24x31 was determined by a scrap piece of plywood I had sitting in the garage.
FYI, I put a single crossmember (not sure what you call it in carpentry world) from front to rear of the frame for both the top surface and bottom frame. My thinking was that it makes it more sturdy and, especially for the top, will "bounce" less if I hammer stuff on it.
My bench is made of cabinets/shelves below, with a 30"x96" Solid Core door slab as the bench top. I designed it to use both standing or sitting on a bar stool. The bench top is 39" tall. Plenty of space for up to 8 presses or other equipment such as lubesizers and other bench mounted tools. Currently I have 2 Dillon 550's, a Rockchucker, Lam II, Uniflow measure, RCBS bench mounted priming tool, and Dillon Super Swage 600. I interchange some of my bench mounted tools by mounting them on a piece of 1x pine board and clamping them to the bench with C- Clamps. This makes it easy to change things around if need be. Also plenty of storage space below for reloading gear.
Attachment 255516
The seat on my tall wheeled swivel chair is 23 inches tall and my bench is 33 inches tall. I do all my reloading seated. I’m 6’4 with long legs. Works well for me. I use 4 of the 4 spring adjustable arm desk lights mounted above my bench on my shelving so they can be adjusted to point anywhere they are needed as I have 5 reloading presses set up on it and one more on a pedestal.
Last edited by Baltimoreed; 01-27-2020 at 09:38 AM.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |