Lyman Bushings: H-G, H-G, H-17, H-15, and H-10. Anyone need them?
Lyman Bushings: H-G, H-G, H-17, H-15, and H-10. Anyone need them?
I could definitely use some 223 brass if anyone has any. I am also looking for a 309 sizer (Lee) as I am converting cases to 300 Blackout. I am a very new caster...just cast my first boolits this past weekend and it is ADDICTING!! haha!! I love it! I bought a small Lee Precision 5 pound melter...should've gone larger because I use a tiny ladle and it takes a LOT of patience...First batch, I got 3 good ones (I say this loosely)...out of 30. Second batch, I only had to throw 5 back for remelting (out of about 50).
I love this site and all the knowledge it's got.
Si vis pacem, para bellum
Could use one of the "lace-on" comb raisers as seen on some the older rifles.
Last edited by bbogue1; 04-18-2017 at 06:57 AM.
Okay had a crazy week of doctors office visit and PT , tests etc.
Now to relax some.
Here is a list of items that people are looking for or I have :
HAVE :
Lyman Bushings: H-G, H-G, H-17, H-15, and H-10 ( dsh1106 had the H-G already)
MEC : shotgun reloader parts ask. Getting ready next month to start selling presses, and extra parts. Darn I been reloading shot shells too long. I have a mess parts.
LOOKING FOR:
Baryngyl dies in , 9mm and 40 S&W also need 30-30 dies.
bbogue1 needs a set of die; 45 Auto dies (I have the dies but no stems yet ( BrassMagnet may have them) need to clean them up and check the dies out better) . And also looking for a press ( maybe he has found one). 9mm .357, .358 molds .
.40 dies for my son- in-law then.45 does for my friends grandson *****. After that I am looking for .358 molds and .41 and .452 molds. Then comes sizers for .357 .41 and .451
a trimmer would Be so nice for ***** to use with his Russian rifle. I have trimming tools for 9mm and 38 Special but not .40 or .45.
Neither ++++ nor ***** have calipers.
Boxes for round storage are always welcome(using Dollar Tree plastic containers now).
buggybuilder "lace-on" comb raisers as seen on some the older rifles.
hwilliam01a mold for the 32 Winchester Special, and sizing die (??) and help on using them.
cptjack can use the 35 molds. Redding scale #1 or #2. need pan and hook.
brstevns http://castboolits.gunloads.com/memb...?3868-brstevns Needs a 358 Winchester seater die that crimps.
Okay that about it for now.
Teddy
Last edited by Teddy (punchie); 06-01-2017 at 07:53 AM.
I am really in need of a 358 winchester seating die that also crimps. Would not ask if I had the funds to purchase one.
Not going to have the seater my items.
Just looking for other ideas for doing your job. Would any .388 seater work?
Years ago I was always taught to crimp turn the seater die down down just enough to crimp the edge of the neck. But to do this brass must be all the same length. Looking at case size etc., would a 35 rem maybe work if set just so. ?? its .04 off on neck size and bullet is the same .04 smaller. I'm wrong its with in a .01 or the same on bullet size. Would a different 35 caliber seating die work is what I'm getting at.
Maybe someone else may have just what your looking for.
Thanks. Been looking on Ebay every day. Bought a 323470 two cast mold that needed a sprue plate and a couple of screws. Got mold for 40 bucks and all the parts for $10 bucks. question I have is will 323 be ok instead of the 321. Do I need to resize them and that is where I cannot find a Lee resizer and Lyman dies are around, but need a Lyman resizer press to use them as they are not interchangeable.
.
I need a powder measure and a dribbler. I been using lee dippers.
I also need a flat seat stem for lyman dies to fit 30-30. I can make any shape work though.
Last edited by Bazoo; 06-01-2017 at 09:08 PM.
Yes sir , a flat nose seater stem for a lyman 30 caliber die.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |