Is it just 2cycle oil? or is it something worth only using.
others have mentioned 2cycle oil, is that a good or bad idea? bees wax sure was a bad idea. **** was messy as ill get out.
Is it just 2cycle oil? or is it something worth only using.
others have mentioned 2cycle oil, is that a good or bad idea? bees wax sure was a bad idea. **** was messy as ill get out.
Bullplate.
ΜΟΛΩΝ ΛΑΒΕ
Je suis Charlie
Remember Lavoy!
I'll cling to my God and my guns, and you can keep the "Change".
how often do you lube?
They have a website? all google shows me is casting forums
They use Bullplate. But any full synthetic two stroke oil will do the same thing. No point paying more for a repackaged product.
Personally, I think the Bullplate works much better than synthetic 2 stroke oil. You mileage may vary. Here's the link to it on Noe's site. One drop of it is usually sufficient for one lengthy casting session. A little goes a long way. http://noebulletmolds.com/NV/product...89qi2vjl0b50a2
I have been using a little bottle (maybe 2 oz. at most) from Bonanza for years. It started running low. So, I tried some Lucas "Upper Cylinder Lubricant and Injector Clearner. I had a 5.25 oz. bottle laying around shop. It does a fantastic job. I will be dead before that is all used up.
Any reason not to just use Neverseize?
Al told me the secret ingredient is Gypsy tears!
Try dielectric silicone grease. I have had good luck with it.
Seems folks are talking about a couple different uses; bullet lube and mold lube. For my molds I use Bullplate (I know 2-cycle works too, but I'll support a member any time I can). I also make a bullet lube; 3-1 Beeswax to Bullplate.
http://bullshop.weebly.com/-lubes.html
My Anchor is holding fast!
Synthetic 2cycle mould lube works, but will migrate into cavity and contaminate if too much is used. I use a very very small drop on hinge bolt area and neverseize on alignment pins.
LBT mould lube (beeswax and graphite) work best, but is very messy if too much is used.
I have been using Marvel Mystery Oil for over 60 years and have yet to stick a case with it.
wmitty never seize would probabley work fine but would be messy,I have never used it but STP should be good, I would try cutting it with a mineral sprite or a light oil of some kind or it may be too thick.
Are my kids/grandkids more important than "o"'s kids, to me they are,darn tooting they are!!! They deserve the same armed protection afforded "o"'s kids.
I have been hoodwinked but not by"o"
In God we trust,in "o" never trust
Support those that support the Constitution and the 2nd Amendant
ΜΟΛΩΝ ΛΑΒΕ
Je suis Charlie
Remember Lavoy!
I'll cling to my God and my guns, and you can keep the "Change".
Some claim syn 2 cycle is the same , & will work ,but it migrates more & has to be renewed more often
BullShops BullPlate Lube is Gooder!!!
GP100man
I have never used anything but Bullplate so can't compare it to anything else. What I can say though is that if I forget to put it on I have much more trouble. Then I realize what I forgot, lube up and everything is good.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |