K-31 311-180Gr NOE Group Buy

[SwedeNelson]

For information on this buy see “K-31 Mould”
http://castboolits.gunloads.com/showthread.php?t=45919


K31 311-180Gr


Should fit very well.

This is how N.O.E. is going to run our group buy.

You can ether PM or E-mail me at (pbsco1 @ qwestoffice.net) with
what you want. Will post a running list of user name and how many
cavities / options. When we get 15 on the list the order will go in for
the tooling. It takes two to three weeks for the tooling to get in.
We will keep the buy open until the tooling gets in.

At that time we will close the buy and ask you to send in your
payment.

It will take another three to four weeks to run the moulds.

Prices will be as follows:
Single cavity mould $68.00 Ea.
Double cavity mould $72.00 Ea.
Three cavity mould $79.00 Ea.
Four cavity mould $85.00 Ea.
Five cavity mould $92.00 Ea.
Plus Shipping/Handling.
Prices are subject to change at any time.

You can mix number of cavities in an order to make 15.
We will offer gas check only on this bullet.

Use LEE Commercial 6-Cavity handles (not included).
Lyman, RCBS type top punch furnished with each mould
as well as a sample of Bull Plate sprue plate lube.
Moulds are machined from 2024 Aluminum
Used for high strength structural and aircraft applications.
Tensile strength range 30,000 to 63,000 psi
Sprue plate (blued), alignment pins, and hardware will be
carbon steel.

Hollow pointing one cavity and furnishing a double
ended pin would be $35.00 Extra.

We will accept Checks, Money Orders and Pay-Pal
Pay-Pal requires a 3% sir-charge.

Our mailing address is:
Night Owl Enterprises
1645 W 150 N
Provo, Utah 84601
801 377-7289

Zip Code List
06110 France
68409
45840
81003
15401
68776
83276
31545
55416
40071
76367
08043
46755
80004
30436
27713
85260
52245
80015
51031
57107
32547
DH3 2AY
67062
44286
16316
96822
44233
64117





Thank you for your interest in this buy.
Swede Nelson

[SwedeNelson]

List of orders:
*1 kirb 2 cavity w/HP
*2 dominicfortune00 4 cavity
*3 primersp 2 cavity
*4 dromia 5 cavity
*5 j20 owner 2 cavity w/HP
*6 emmie 4 cavity
*7 rigger 4 cavity
*8 280Ackley 4 cavity
*9 RugerFan 4 cavity
*10 35Whelen 4 cavity
*11 Mike in co 4 cavity
*12 wrench 2 cavity
*13 Swiss96/11 5 cavity
*14 Jvg5576 2 cavity
*15 vintageRifle (2) 3 cavity
*16 Glenn R. Latham 4 cavity
*17 Madesnshooter 3 cavity w/HP
*18 boz330 2 cavity
*19 techlava 5 cavity w/HP
*20 azhunter12 5 cavity
*21 62fusil 4 cavity
*22 dan 3 cavity
*23 JMN322 3 cavity
*24 mtgrs737 4 cavity
*25 4060MAY 4 cavity
*26 6shooter 3 cavity
*27 45-70bpcr 4 cavity
*28 B747 4 cavity
29 BobJ 5 cavity
*30 NuJudge 5 cavity

Thanks
Swede Nelson

[dominicfortune00]

I'll take a 4 cav.

Will get order out on Tuesday.

Oops, make that when the funds are requested.

[j20owner]

Omg!!!!

[primersp]

i'will take a 2 cav

[dromia]

PM sent Al.

[280Ackley]

Swede you're killing me. I'm away from my computer for a long weekend and come home to find not one, but two new moulds I want/need? Put me down for a 4 cavity.

[RugerFan]

I'm in for a 4 cav.

[35 Whelen]

PM, e-mail, Western Union Telegram, Fax, smoke signal, and telegraph sent....I'm in for a 4-cavity.
35W

[RugerFan]

So now I notice the alloy used for the drawing dimensions is linotype. How many folks are really going to be casting this bullet in linotype? What would the dimensions look like casting with WW or Lyman #2?

[SwedeNelson]

RugerFan

We will cut the mould to cast the same dimensions the only change will be the weight.
It will weigh about 192Gr.

Good catch!
Thanks
Swede Nelson

[RugerFan]

RugerFan

We will cut the mould to cast the same dimensions the only change will be the weight.
It will weigh about 192Gr.

Good catch!
Thanks
Swede Nelson

Ok, just checking.

Also, I finally got to the post office today and mailed you a few 266469 bullets. You should get them this week.

[Calamity Jake]

Your also running a 314299 clone, what are the chances of getting 2 cavs each in a 4 cav mould?

You know somebody had to ask!!!!

[mike in co]

i just shot some 314299's(210/1700 pfs) from a tired finn m39, and shoot a 97-2x at 200 yds, iron sight...guess i need a heavy for my stable of k-31's too.

count me in for a 4....

mike in co

[swiss 96/11]

I am in for a 5-cavity,great bullet weight and custom fit for the K-31's.

[jvg5576]

PM sent for one 2-cav. mould.

[VintageRifle]

I will take two 3-cavity moulds.

[SwedeNelson]

That makes 15.
Will order the tooling today.
And start to PM every one with a cost.
The tooling is running about 2 to 2 1/2 weeks.
So we will keep the buy open until we get
it in - for any that would still like to get in.

Thanks for the orders
We couldn't do it with out you.
Swede Nelson

[jvg5576]

payment mailed today

[primersp]

it's seem i was 2 times for the mold on the list ,i want only one please ,paiement send
thanks