Long handled forceps is my huckleberry. I have one straight jaw and one with curved jaws. The curved jaws are the ones I use for handling the bullets and I've found lots of uses for the straight jaw pair.
I'll have to look at copper mats.
Long handled forceps is my huckleberry. I have one straight jaw and one with curved jaws. The curved jaws are the ones I use for handling the bullets and I've found lots of uses for the straight jaw pair.
I'll have to look at copper mats.
She gave me a well used Yoshi copper bake and grill sheet. She gets her foil and parchment paper rolls back now. Lays flat, cut to size with scissors, lasts a lifetime. Nothing sticks to it.
Whatever!
I use them for non gas checked bullets. If I stand up GC boolits on silicone mats the PC flows outwards on the bases. Even with a thin coat it's a struggle to get GCs on. I use a mesh tray set on a baking pan lined with tin foil for my GC boolits so PS flows under the base instead of around the base. The GCs go on alot easier this way
It's a $5 mesh pan I bought from Walmart. My 44 and 45 cal dont fall over on it when moving it into the oven. A few of the 35s fell over today and never left road rash from laying down. I use silicone mats for my 255 grain 45 colts
These are lee 240 grain .430 HP’s on my mesh tray....
The only bad part is the excess PC sticks to the mesh and comes off eventually on other boolits being PC’d. The GCs go over it anyways.
Last edited by Tripplebeards; 08-06-2020 at 08:14 PM.
Just got my Yoshi copper sheets in - I'm looking forward to trying these out and comparing to the non-stick aluminum foil and the silicone sheets I have been using.
I definitely prefer the silicone sheets. They lay nice and flat, and the powder adheres to the bottom of the bullets better than with parchment. Parchment paper also browns eventually and becomes crumbly.
I use these: Silicone sheets (Amazon link)
Quarter sheets fit my quarter sheet baking pans perfectly. Unfortunately I will now need some more baking pans for my smoker.
Only bad part about the sheets is residual PC that has melted from previous bakes always releases on my current boolit bases. Here are some I just baked with smokes purple mixed with black. You can see blue, yellow, and orange stuck to the bases from previous bakes. Doesn’t hurt anything but it’s annoying.
I see this transfer of colors more of a problem when using the mini ice cube trays.
Nice lookin color TB!! ♥️
CW
NRA Life member • REMEMBER, FREEDOM IS NOT FREE its being paid for in BLOOD.
Come visit my RUMBLE & uTube page's !!
https://www.RUMBLE.com/user/Cwlongshot
https://youtube.com/channel/UCBOIIvlk30qD5a7xVLfmyfw
Just because a PC'd boolit passes a hammer test doesn't mean it's cured enough so that it won't react/get melted by some smokeless powders
I tested some purposely under cured boolits 15 minutes in a preheated convection oven
Bullseye powder
this powder will not burn properly.
It's your choice!!!
You spend all this time reloading what's a few more minutes baking the PC'd boolits to prevent this possibility?
I don't use Bullseye powder so I cannot comment on that. I have recovered bullets with the powders that I use and have never found a boogered up base from powder attacking the coating. You are correct that the bake time increase is minimal so I would certainly recommend anyone using Bullseye powder to bake to the recommended time.
Jim
"The problem with quotes on the internet is that it is hard to verify their authenticity." - Thomas Jefferson 1803
Bullseye is simply the powder tested. Dont for a minute think its the only one.
Its been said that Improper process yield piss poor results...
CW
NRA Life member • REMEMBER, FREEDOM IS NOT FREE its being paid for in BLOOD.
Come visit my RUMBLE & uTube page's !!
https://www.RUMBLE.com/user/Cwlongshot
https://youtube.com/channel/UCBOIIvlk30qD5a7xVLfmyfw
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |