StainLess Steel MediaTitan ReloadingGraf & SonsADvertise here
Lee PrecisionMidSouth Shooters SupplyRotoMetals2Inline Fabrication

Tab Content
  • popper's Avatar
    Yesterday, 05:51 PM
    popper replied to a thread Crony setup advice in Factory Rifles
    I don't shoot for groups and chrony at the same time. Just set the chrony when looking back at the barrel.
    11 replies | 178 view(s)
  • popper's Avatar
    Yesterday, 04:30 PM
    Adam - cast the S.H. into boolits so you can add just a bit at a time. Add just a bit to t he pot of your R.S. to see how much is needed. Load some dummies for fit & function/size, then test/shoot some. If not right, recycle then add a bit more. ...
    14 replies | 246 view(s)
  • popper's Avatar
    09-23-2017, 03:14 PM
    45ACP, 38 are low pressure loads so the 'soft' works. 9, 357 & 40 are not low pressure. Other problem with soft for rifle is trying to prevent swelling of the nose when seating. Just pulled a dozen for the BO that wouldn't chamber. The 30/30 is a...
    41 replies | 1015 view(s)
  • popper's Avatar
    09-23-2017, 02:48 PM
    Roto says that testing an ingot doesn't work due to grain struct. of the high Sb alloy. Should be 36 or so.
    15 replies | 1310 view(s)
  • popper's Avatar
    09-23-2017, 11:22 AM
    I actually ended up with 6gr of cfe pistol & shot in 1:8 10" BO pistol. Unfortunately the adj. GB is fouled so will not cycle the AR. Accuracy is decent with SeeAll sight @ 50 & just a front stand.
    11 replies | 727 view(s)
  • popper's Avatar
    09-21-2017, 07:47 PM
    OOB thought was incorrect - looking closely at the case head - what is left of it. Totally extruded into the bolt face. Bolt had to be locked up. I'd be surprised if it unlocked by gas pressure at all. edit: yes the primer was dented. No there...
    75 replies | 2392 view(s)
  • popper's Avatar
    09-19-2017, 10:56 AM
    Slam fire due to bad HS I assume. IIRC, I tossed that brass but saw no damage to it. I've gone through >500 rnds since then, no problem. Found case a LONG way from incident. Also had a total case head separation in 40SW. Recovered the case head,...
    75 replies | 2392 view(s)
  • popper's Avatar
    09-18-2017, 08:14 PM
    Sorry, that is a myth. DPMS (pre-buy-out) factory 308 carbine. Shoulder just a hair too long. 40.5gr 4895 under a 165 cast. Safety ON and trigger NOT pulled. Nice chunk of concrete missing. Nothing through my shoulder, did take a long time...
    75 replies | 2392 view(s)
  • popper's Avatar
    09-18-2017, 02:27 PM
    dimaprok 50yds ~1700 fps 185gr GC with BLL. I'm not that great a shot but I don't see any 'fliers' there. At least it was below 100F that day. Gray powder is tin, brownish is zinc.
    41 replies | 1015 view(s)
  • popper's Avatar
    09-18-2017, 02:03 PM
    Just not going to happen with an AR. And when YOU have had one - OOB - , you will believe that even the design can be beat. It is NOT a myth. I agree that you MUST do a chamber check on a FTF in ANY gun.
    75 replies | 2392 view(s)
  • popper's Avatar
    09-17-2017, 10:55 PM
    Look at the thickness of the broken steel at the bottom of the carrier!
    75 replies | 2392 view(s)
  • popper's Avatar
    09-17-2017, 10:36 PM
    I've bought 'once fired' and found it wasn't. IIRC amscore uses a stepped brass vs tapered case. If actually from a range it's probably ok. I did use an FC 40 that blew the case head off, known & recalled but somebody used it.
    18 replies | 718 view(s)
  • popper's Avatar
    09-17-2017, 07:34 PM
    I'll swag it. Dirty chamber at shoulder and a poor carrier. Seen too many that have very little metal at the mag lip area. OOB fire. Case blew out through the feed ramp, took out extractor & bottom of carrier.
    75 replies | 2392 view(s)
  • popper's Avatar
    09-17-2017, 03:01 PM
    I tried the lead in the pot thing, got tired of cleaning lead off. Got tired of cleaning the candle gunk off the cases too. Just use the torch and my fingers.
    22 replies | 695 view(s)
  • popper's Avatar
    09-17-2017, 02:59 PM
    So it appears the primary problem is with LP that have a small flash hole and large area under the primer. The tolerance of any chamber/ammo will allow the primer to move relative to the case. The primer MAY get smashed back into the pocket. ...
    24 replies | 524 view(s)
  • popper's Avatar
    09-16-2017, 07:53 PM
    popper replied to a thread Stirring the pot in Casting Equipment
    Old putty knife & slotted SS spoon from WW.
    29 replies | 1010 view(s)
  • popper's Avatar
    09-16-2017, 02:00 PM
    Had the wet problem from a burst pipe. Mostly rifle & pistol. So far they are fine.
    16 replies | 408 view(s)
  • popper's Avatar
    09-16-2017, 10:22 AM
    Note to self - do NOT used enlarged flash hole brass for standard loads! I used to shoot a lot of light loads in 30/30 thin brass (but it is rimed H.S.). Never noticed the problem even when I (mistakenly) used magnum LRP. It is the delay between...
    24 replies | 524 view(s)
  • popper's Avatar
    09-15-2017, 02:04 PM
    Don't know if it is really set back as I think of. Primer pops, pushed the case back to the bolt and the powder charge pushes the shoulder FORWARD. Opening up the flash hole is an attempt to get the powder to light right away. Head space is the...
    24 replies | 524 view(s)
  • popper's Avatar
    09-14-2017, 10:27 PM
    Thermoset. Uk
    9 replies | 308 view(s)
  • popper's Avatar
    09-14-2017, 02:57 PM
    Melted some culls today, yesterday I processed a hundred 30/30 cases and several hundred 40sw, primed & ready. Actually spending time to learn all but drum parts of 'Apache' (Jorgen Ingmann) without the overdubs. Venture's release helps some. ...
    4854 replies | 347607 view(s)
  • popper's Avatar
    09-14-2017, 12:05 PM
    There is a story (true) of a kid shooting a B.B. with 12ga slug, bear got a bite on the kid who had to basically walk to camp to get rescued. A wounded (3 legged) pig gets 100 yds in ~10 sec., bears are faster. 00 do anything but tick them off...
    52 replies | 2100 view(s)
  • popper's Avatar
    09-14-2017, 10:59 AM
    I got pure to work in a hot load for 180gr. 40sw by adding Zn, ~1% with a tad of Cu. PC helps but just barely,AC. They will drop shiny, heavy & small so PC should help. Best solution though is to get some superhard, cast into boolits and add as...
    41 replies | 1015 view(s)
  • popper's Avatar
    09-13-2017, 11:17 PM
    Big hatchery at Branson. Fish are pretty soft/ squishy.
    6 replies | 195 view(s)
  • popper's Avatar
    09-13-2017, 11:03 PM
    Interesting loading got BO.
    19 replies | 601 view(s)
  • popper's Avatar
    09-13-2017, 02:12 PM
    IIRC you can only get a certain 'type' in EU, TFIG. Check with your local paint manuf. for non-architectural powder. Their distributors may be able to tell you which distributors sell to the PC shops - unless you want 55gal drums of PC.
    9 replies | 308 view(s)
  • popper's Avatar
    09-13-2017, 02:05 PM
    Bloodman - WD from the mould is 400F to 32F(?) from an alloy that is liquid, ~700F. Grain structure changes with cooling. Fast cooling 'freezes' the grain, locking it's structure. Reheating will allow the structure to 'unlock' some. So - casting...
    20 replies | 930 view(s)
  • popper's Avatar
    09-13-2017, 01:44 PM
    Way too thin a coat. Should be a couple thou. & NOT see through. Wait til you get a thicker coat before honing the sizer. You an double coat, just cook til gloss then STOP. Cool & recoat. Cook normal. ACWW should be hard enough but I don't...
    16 replies | 479 view(s)
More Activity
About popper

Basic Information

Signature


Whatever!

Statistics


Total Posts
Total Posts
6,800
Posts Per Day
2.98
General Information
Join Date
06-28-2011
Referrals
0

1 Friend

  1. Blanco Blanco is offline

    Boolit Master

    Blanco
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check