RepackboxMCD ProductsReloading EverythingInline Fabrication
MidSouth Shooters SupplyTitan ReloadingRotoMetals2Lee Precision

Results 1 to 17 of 17

Thread: straight line penetration

  1. #1
    Boolit Master Oklahoma Rebel's Avatar
    Join Date
    Nov 2015
    Location
    outside of Sand Springs, N.E. OK
    Posts
    2,353

    straight line penetration

    Given the same caliber, and weight, with say a 60 percent meplat, which would have better straight-line penetration, a truncated cone or a ogival design?
    An armed man in a citizen.
    An unarmed man is a subject.
    A disarmed man is a slave.

  2. #2
    Boolit Grand Master In Remembrance
    Join Date
    Aug 2005
    Location
    South Jersey
    Posts
    6,314
    Rebel, not identifying the caliber:
    * Short range, no difference
    * Long range, 100 to 1000yds - ogive
    60% metplat is one fat bullet
    Regards
    John

  3. #3
    Boolit Grand Master popper's Avatar
    Join Date
    Jun 2011
    Posts
    10,717
    No real answer to that question. Heavier works best. A while back I accidentally shot through the wide part of a pine 2x4 (50yds) - nice burrow until the wood split ~ 1.2" from the back edge. Nice RD boolit from jacketed fps load. Pretty much a question of what is in the target to deflect/damage the boolit. Watch some utube gel & wood shots on penetration - they never go in a straight line.
    Whatever!

  4. #4
    Boolit Master maxreloader's Avatar
    Join Date
    Jan 2015
    Location
    Southern March 15th, 1820
    Posts
    671
    alloy wasnt mentioned... the harder the better but not too much or it will severely fragment on impact. Just enough... like the buffalo bore rounds... they penetrate deep.
    Looking for Ideal mold 419181 (44 Evans Long)
    "Joined Dates" are deceiving if you factor-in "lurk" dates.

  5. #5
    Boolit Master Oklahoma Rebel's Avatar
    Join Date
    Nov 2015
    Location
    outside of Sand Springs, N.E. OK
    Posts
    2,353
    the caliber shouldn't matter, as long as both boolit designs are the same weight and caliber, and for giggles lets say lyman #2, but like I said, it really only matters that they are both the same alloy, and fired at the same velocity from the same distance. basically I was asking hoping to find someone who has tried both types.
    An armed man in a citizen.
    An unarmed man is a subject.
    A disarmed man is a slave.

  6. #6
    Boolit Master Oklahoma Rebel's Avatar
    Join Date
    Nov 2015
    Location
    outside of Sand Springs, N.E. OK
    Posts
    2,353
    I meant the caliber should not matter for use in comparing, of course the caliber would make a difference in the amount of penetration. does no one have a mold of each type, at least close to the same weight?
    An armed man in a citizen.
    An unarmed man is a subject.
    A disarmed man is a slave.

  7. #7
    Boolit Grand Master fredj338's Avatar
    Join Date
    Feb 2009
    Location
    kalif.
    Posts
    7,396
    I am not sure shape is as important as the meplat. A RN will often deflect or veer or even tumble. A flat point will usual track straight. It is easier to get a large meplat with ogive than TC.
    EVERY GOOD SHOOTER NEEDS TO BE A HANDLOADER.
    NRA Cert. Inst. Met. Reloading & Basic Pistol

  8. #8
    Boolit Grand Master tazman's Avatar
    Join Date
    Jan 2014
    Location
    west central Illinois
    Posts
    7,718
    The only rifle I have tested that has that large a meplat was a 458 Winchester magnum and this was done about 40 years ago.
    The 2 boolits that I tested were the Lyman 462560 and the Lee C457-500 F.
    These were fired into a red clay bank as a backstop. The were running about 2000fps.
    They were cast from straight linotype.
    Both penetrated very deeply(in excess of 5 feet) and neither one veered from a direct straight line unless it hit a rock. I fired 5 shots with each boolit. I only dug out 2 of each when I found out how deep they were going.
    Unless the boolits struck a rock, they didn't expand or deform and were in perfect shape when I got them out of the dirt.
    I am sorry that I no longer have the slugs(I have moved since then and they were lost).

  9. #9
    Boolit Master


    HangFireW8's Avatar
    Join Date
    Dec 2008
    Location
    Central Maryland
    Posts
    2,587
    Quote Originally Posted by Oklahoma Rebel View Post
    Given the same caliber, and weight, with say a 60 percent meplat, which would have better straight-line penetration, a truncated cone or a ogival design?
    With a 60% meplat, there's hardly any difference between the designs. Also, the question cannot be answered without giving us the calibers of the ogive and the angle of the truncated cone. But I can discuss it a bit.

    Your question can be interpreted 2 different ways:
    1. Which design will penetrate deeper?
    The design with the greater sectional density.

    2. Which will be less likely to be diverted from a straight-line path?
    Again, with a 60% meplat, they will hardly differ. And again, you didn't give enough design information to answer the question. But the answer is, the design that has the most blunt nose.
    I give loading advice based on my actual results in factory rifles with standard chambers, twist rates and basic accurizing.
    My goals for using cast boolits are lots of good, cheap, and reasonably accurate shooting, while avoiding overly tedious loading processes.
    The BHN Deformation Formula, and why I don't use it.
    How to find and fix sizing die eccentricity problems.
    Do you trust your casting thermometer?
    A few musings.

  10. #10
    Banned



    Join Date
    Jan 2011
    Location
    Color Me Gone
    Posts
    8,401
    Look at the results from the Linebaugh Seminars. The WLN or WFN works. The Punch bullets work real good.

  11. #11
    Boolit Master

    Join Date
    Apr 2012
    Location
    State of Denial
    Posts
    4,432
    All things being equal, I'd put my money on the ogival. It's going to have more of it's weight forward; the TC is going to move some of that weight to the rear.

    While the bullets you are describing are not so extreme in their weight-rearward distribution, base-heavy/nose-light is the formula that's used to make the 5.56 NATO and 7.62x39 tumble on impact.

    Keeping more metal up front is also going to give an ogival a sturdier nose that's less likely to deform for any given alloy. That's going to improve ability to track straight.
    WWJMBD?

    In the Land of Oz, we cast with wheel weight and 2% Tin, Man.

  12. #12
    Boolit Master


    HangFireW8's Avatar
    Join Date
    Dec 2008
    Location
    Central Maryland
    Posts
    2,587
    Quote Originally Posted by Bigslug View Post
    All things being equal, I'd put my money on the ogival. It's going to have more of it's weight forward; the TC is going to move some of that weight to the rear.
    How do you know that? It could be a 6 calibre ogive and a 45 degree T/C. The OP gave no numbers.
    I give loading advice based on my actual results in factory rifles with standard chambers, twist rates and basic accurizing.
    My goals for using cast boolits are lots of good, cheap, and reasonably accurate shooting, while avoiding overly tedious loading processes.
    The BHN Deformation Formula, and why I don't use it.
    How to find and fix sizing die eccentricity problems.
    Do you trust your casting thermometer?
    A few musings.

  13. #13
    Boolit Master Oklahoma Rebel's Avatar
    Join Date
    Nov 2015
    Location
    outside of Sand Springs, N.E. OK
    Posts
    2,353
    big slug seems to be the only one to understand my question, and he gave me a very good answer, that satisfies my curiosity. hangfire, oh, nevermind, thanks a lot!-Travis
    An armed man in a citizen.
    An unarmed man is a subject.
    A disarmed man is a slave.

  14. #14
    Boolit Grand Master Outpost75's Avatar
    Join Date
    May 2013
    Location
    over the hill, out in the woods and far away
    Posts
    10,352
    Dynamic stability.

    Center of gravity close to center of pressure.

    Low overturning moment

    Gyroscopic stability factor 2.0 or greater.

    https://library.med.utah.edu/WebPath...S/GUNBLST.html
    The ENEMY is listening.
    HE wants to know what YOU know.
    Keep it to yourself.

  15. #15
    Boolit Master


    HangFireW8's Avatar
    Join Date
    Dec 2008
    Location
    Central Maryland
    Posts
    2,587
    This thread represents why I'm about to give up on this site.
    I give loading advice based on my actual results in factory rifles with standard chambers, twist rates and basic accurizing.
    My goals for using cast boolits are lots of good, cheap, and reasonably accurate shooting, while avoiding overly tedious loading processes.
    The BHN Deformation Formula, and why I don't use it.
    How to find and fix sizing die eccentricity problems.
    Do you trust your casting thermometer?
    A few musings.

  16. #16
    Boolit Master Oklahoma Rebel's Avatar
    Join Date
    Nov 2015
    Location
    outside of Sand Springs, N.E. OK
    Posts
    2,353
    what he understood and you didn't is that I was talking about just your average design of each kind, if I said keith or spitzer, instead of truncated cone and ogival, would you have answered the same? I have seen tons of keith based boolits, but you would have assumed the 429421 right? or would you have asked, well what if he meant the accurate # so and so? but you can let it get under your skin, just don't forget, instead of getting your feeling riled up, you could always push the back button, and your day would go on just like it would have, if you wanted to.
    Last edited by Oklahoma Rebel; 01-06-2018 at 12:14 AM. Reason: cuz i called it a "spritzer" hehehee
    An armed man in a citizen.
    An unarmed man is a subject.
    A disarmed man is a slave.

  17. #17
    Boolit Master Oklahoma Rebel's Avatar
    Join Date
    Nov 2015
    Location
    outside of Sand Springs, N.E. OK
    Posts
    2,353
    fred, your answer makes a lot of sense, and taz, with the 458 Winchester, I doubt I'd be as worried about penetration! lol thanks guys
    An armed man in a citizen.
    An unarmed man is a subject.
    A disarmed man is a slave.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check