i've got the 45-75, 28.0 grs AA 5744 and an Oregon Trails 350 gr FN, shoots 1400 fs....love it....
It didn't work well, by the time I got to shooting the 59gr load had lengthened!! Too much compression I guess. I should have crimped the bullet it place. Anyway, I single loaded 1 and it kicked like a mule. I went through all the measuring again, searching for no more than .125 compression and still using the .060" wad. I ended up with 55 gr of Old Einsford FF with .110 compression under the BACO 300 gr bullet and crimped it this time. Shoots very well and the recoil is as much as I want to endure with that masochistic, curved, rifle butt plate. I'll report back when I get an average group size and chrono data.
"There's a Fine Line Between Hobby and Mental Illness"!
Howdy Irascible
I think you were asking me if the sight stem was to long to sight in at 100 yds. i got from Brownells , the answer is yes , that is why I had to solder a brass bar on the front sight.
I also size my cast bullets to .459
No, it was somebody else suggested a taller sight. I answered that you had already done that.
"There's a Fine Line Between Hobby and Mental Illness"!
Greetings
Get yourself a "curved buttplate leather cover". Have one on our 50-95 and recoil is no issue. 350 grains at 1465 fps. 85 + grains of 3F.
But then we seldom shoot on a bench with fat caliber rifles. Cross sticks with a bit of practice will give you groups that are near as good as a bench.
Mike in Peru
"Behold The Lamb of God that taketh away the sin of the world". John 1:29
Male Guanaco out in dry lakebed at 10,800 feet south of Arequipa.
Just bought one from Kirkpatrick.......Helps a lot
"There's a Fine Line Between Hobby and Mental Illness"!
Just for the heck of it I looked on you tube under 1876. I watched one fellow who made a big deal of pushing the last loaded round to the left after it was in the magazine tube. I tried it. darned if it didn't help. WHY? Is the elevator a one size fits all to accept the 45-75 and 50 caliber and thus too large a diameter to correctly align the thinner cartridges? If so, it would seem that one could sleeve the hole for the smaller cartridges. Maybe? Or is it for another reason?
"There's a Fine Line Between Hobby and Mental Illness"!
Good morning
Remember the lifter also has to permit the rim to pass completely through during the loading process. The excess diameter makes side gate loading possible without forcing the loaded round to "bend around the corner". The straight line "tube" loading of the Henry never faced this issue.
Plus if you are loading to max length, the last loaded round has to have the rim sitting flush with the receiver wall. If the round is sitting at an angle it is "to long" in that canted position. The nose edge or the rim edge is going to catch. By squaring that round in the lifter it will be less apt to get the rim and nose past the receiver edges on the way up.
"Behold The Lamb of God that taketh away the sin of the world". John 1:29
Male Guanaco out in dry lakebed at 10,800 feet south of Arequipa.
Thanks, I was thinking of making some brass about .020 longer, full length of the elevator. Maybe that's not a good idea. I'll study it some more tomorrow, plenty of time while the snow is falling. 2-4 inches, but it should be all gone by Saturday.
"There's a Fine Line Between Hobby and Mental Illness"!
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |