Reloading EverythingInline FabricationTitan ReloadingMCD Products
RotoMetals2RepackboxMidSouth Shooters SupplyLee Precision

Page 1 of 6 123456 LastLast
Results 1 to 20 of 115

Thread: Browning Citori blew up!

  1. #1
    Boolit Master Blood Trail's Avatar
    Join Date
    Apr 2014
    Location
    Lone Star State
    Posts
    1,573

    Browning Citori blew up!

    I was at the gun club up the road from my father in laws house shooting 5 stand. In the lodge was a Browning Citori sitting on the counter in pieces....and I do mean pieces.

    Strange thing about this is the gun blew at the receiver, sending sharp shrapnel everywhere. The fore end broke to pieces. The stock cracked all the way through. I've seen my fair share of blown up shotguns, but never at the receiver. That's extremely rare.

    The rib is peeled back and there is no way you can straighten it by hand.

    Take a look at the window frame where pieces of the receiver hit. There is no doubt in my mind that had this hit the face or chest, it would have been fatal. The guy was not injured.

    He was shooting reloads (old Remington Peters hulls). This was NOT a squib or stuck wad as the barrel is not split. It's possible that a wad may have got stuck in the forcing cone, but I doubt it.

    Anyway, it's a miracle the guy is fine.


    Sent from my iPhone using Tapatalk
    Last edited by Blood Trail; 06-19-2020 at 01:05 PM.

  2. #2
    Boolit Master Blood Trail's Avatar
    Join Date
    Apr 2014
    Location
    Lone Star State
    Posts
    1,573



    Sent from my iPhone using Tapatalk

  3. #3
    In Remembrance Skunk1's Avatar
    Join Date
    Jan 2014
    Posts
    464
    Glad I wasn't behind that. Glad the gent is ok.

  4. #4
    Banned
    Join Date
    Sep 2009
    Posts
    761
    Looks like a serious double charge there a friend did the same thing with a O/U Winchester very similar in nature pictures.

  5. #5
    Boolit Grand Master OS OK's Avatar
    Join Date
    Dec 2015
    Location
    El Dorado County, N. Ca.
    Posts
    6,234
    Holy cow, a shotgun, of all the weapons...looks like there was C4 in there.
    a m e r i c a n p r a v d a

    Be a Patriot . . . expose their lies!

    “In a time of deceit, telling the truth is a revolutionary act.” G. Orwell

  6. #6
    Boolit Master

    Hogtamer's Avatar
    Join Date
    Mar 2013
    Location
    East central GA, Appling near Augusta
    Posts
    3,394
    That barrel had to be plugged solid. Maybe a 20 ga shell dropped in first? There was nowhere for that charge to go, thus the shrapnel, and it wasn't just a wad. Wow
    "My main ambition in life is to be on the devil's most wanted list."
    Leonard Ravenhill

  7. #7
    Banned
    Join Date
    Nov 2012
    Location
    Central Virginia
    Posts
    7,438
    Quote Originally Posted by Hogtamer View Post
    That barrel had to be plugged solid. Maybe a 20 ga shell dropped in first? There was nowhere for that charge to go, thus the shrapnel, and it wasn't just a wad. Wow
    My thoughts exactly.

    Notice how the mono block failed but the barrel just in front of the mono block has a clean break. I bet if you looked downrange you would find a severally damaged 20 gauge shell that exited the end of the barrel.
    Last edited by Petrol & Powder; 12-29-2016 at 09:32 AM.

  8. #8
    Boolit Master


    Join Date
    Jun 2009
    Location
    North central Ohio/Roane County, W.Va.
    Posts
    1,504
    Does the base of the old Remington Peters hulls have a solid plastic base or paper?
    “Let us endeavor so to live that when we come to die even the undertaker will be sorry.”
    ― Mark Twain
    W8SOB

  9. #9
    Boolit Master

    376Steyr's Avatar
    Join Date
    Aug 2006
    Location
    South Idaho
    Posts
    1,500
    There is a wrecked Model 870 hanging on the wall of my club with similar damage; receiver bulged and barrel peeled back over the chamber. "Bad reloads" were blamed, but I highly suspect it was a 20 gauge shell stuck in the forcing cone. Every now and then I'll find a red 20 gauge hull on the ground at the skeet range, as somebody shoots some very old ammo.

  10. #10
    Boolit Master
    Join Date
    Nov 2008
    Location
    coastal north carolina
    Posts
    1,121
    If it was a barrel obstruction, it had to be right in front of the chamber or if it was up the barrel, the bulge would be prominent. I don't think a double charge would do this and a double charge would fill the case until it wouldn't crimp. Possibly the base wad was gone, but that would have probably not crimped right. I don't know what would happen if there was no base wad, but that looks to be where the explosion took place. I don't know if the base wad is molded into the case like a AA, or if it has a plastic insert base wad. I doubt it was a barrel obstruction or an over charge and if that hull used a separate base wad, I would think that is the most likely scenario.

  11. #11
    Boolit Master Blood Trail's Avatar
    Join Date
    Apr 2014
    Location
    Lone Star State
    Posts
    1,573
    Just got a call from the owner. He said Browning suspects a loose base was from reloads for lodged in the forcing cone. Apparently, this is the #1 reason shotguns fail at the receiver.


    Sent from my iPhone using Tapatalk

  12. #12
    Boolit Master kenyerian's Avatar
    Join Date
    Dec 2011
    Posts
    977
    That makes you stop and think. Very lucky that no one was seriously hurt. Had a guy blow up his 1100 beside me using his special shoot off load but it wasn't that severe. He got some gas burns and some light shrapnel and his receiver was ruined but he got off very lucky.

  13. #13
    Boolit Grand Master

    Beagle333's Avatar
    Join Date
    Mar 2012
    Location
    Back in the woods a piece, just outside Auburn, AL.
    Posts
    5,499
    Wow. That's an expensive kaboom. Glad he's okay!!!!!
    KE4GWE - - - - - - Colt 1860, it just feels right.

  14. #14
    Boolit Master


    Soundguy's Avatar
    Join Date
    Oct 2016
    Location
    N Central Florida
    Posts
    2,902
    Wow.. If a loose bad wad did that, pressure must have spiked with not being able to push the train thru the tunnel... Ouch

  15. #15
    Banned

    Join Date
    Dec 2007
    Location
    soda springs Id.
    Posts
    28,088
    look at the brass right at the front of the chamber where the barrel went.

    I remember Remington coming around back in the day inserting their new base wads in the barrel and then shooting them out with a shell behind them.

  16. #16
    Boolit Master


    Soundguy's Avatar
    Join Date
    Oct 2016
    Location
    N Central Florida
    Posts
    2,902
    With that brass ring.. Think I was a 20 up there making a log jam?

  17. #17
    Boolit Master
    JWT's Avatar
    Join Date
    Apr 2014
    Location
    Outside Detroit
    Posts
    552
    My first thought was a 12 behind a 20.

  18. #18
    Boolit Buddy



    Join Date
    Dec 2011
    Posts
    111
    Hard to tell from picture, but I believe that is not "brass" from a case head but you are seeing the solder joint from the mono block. Also where is the plastic case? If there was a blockage there would be pieces of the case left in the chamber. No, this was a serious high vel. detonation. Remington target hulls are compression formed, no base wad to shoot loose. They haven't used a target hull with a separate base wad since the 60's when the RXP hull replaced their "target hull".

  19. #19
    Boolit Master Cap'n Morgan's Avatar
    Join Date
    Jun 2008
    Location
    Denmark
    Posts
    1,484
    Double powder load! It is virtually impossible to blow a shotgun chamber with a "normal" obstruction - some has even survived the notorious 12 gauge on top of a 20 gauge mistake.
    Cap'n Morgan

  20. #20
    In Remembrance bikerbeans's Avatar
    Join Date
    Feb 2013
    Posts
    1,988
    Did the shooter hit the pidgeon?

    BB

Page 1 of 6 123456 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check