RCBS thermometer.

[ruizhernandeztrust]

Hi,
I have the bad feeling my RCBS thermometer is way off. Ambient temperature at the moment of photo was 79F and the thermometer is reading about 0F (note: it's not reading 970F). The thermometer isn't that old. Anything I can do to fix it? I have no job at the moment and almost broke, I can't afford to buy another one at the moment. I hope to fix it myself if possible but I don't know how to open it. Any help on this matter will be appreciated, best regards!

[largom]

Put the thermometer in boiling water. Should read about 212 Deg.

[ruizhernandeztrust]

Put the thermometer in boiling water. Should read about 212 Deg.

I'll do it right now and I'll post the results. Thanks!

[ruizhernandeztrust]

Full boil reading. Doesn't look good, I've never dropped or mishandled the thermometer. Which are my options now?

[theperfessor]

I'd start with a polite conversation with the Service department at RCBS. They have a pretty good rep for making things right.

[largom]

As theperfessor said. I am sure RCBS will replace it if you send it back to them.

Larry

[Hardcast416taylor]

RCBS - 1-800-533-5000

Robert

[ruizhernandeztrust]

Thanks guys, I'll contact RCBS and hope for the best.

[bhn22]

But what does it read in molten lead? The reason you see it in negative numbers is because the internal coil is at full rest. This thermostat won't start to read temps accurately until they get pretty high. probably over around 2-300 degrees. My Lyman thermometer does exactly the same thing. The fact that it moved at all is a good sign. If you're in the mountains, the altitude would affect the boiling point for water, dropping it dramatically. Water boils in Denver for example, at just under 200 degrees F.

http://www.engineeringtoolbox.com/bo...de-d_1344.html

[Mike W1]

Usually there's a nut on the back side of the thermometer. If there is put it in boiling water and adjust accordingly.

[ruizhernandeztrust]

But what does it read in molten lead? The reason you see it in negative numbers is because the internal coil is at full rest. This thermostat won't start to read temps accurately until they get pretty high. probably over around 2-300 degrees. My Lyman thermometer does exactly the same thing. The fact that it moved at all is a good sign. If you're in the mountains, the altitude would affect the boiling point for water, dropping it dramatically. Water boils in Denver for example, at just under 200 degrees F.

http://www.engineeringtoolbox.com/bo...de-d_1344.html

. In my case when I see the lead start to melt the reading of the thermometer is around 450F (lead melting point is around 621F) so it's +/- 171F off the mark.
. My elevation is a little over 175' above sea level.

I'm planning to cast some bullets this week and I can give more precise numbers.

171F off the mark is acceptable or I'm too anal about this?

***edited***
I meant 450f not 550F

[ruizhernandeztrust]

Usually there's a nut on the back side of the thermometer. If there is put it in boiling water and adjust accordingly.

No nut unfortunately (I think) What do you think?

[Jon K]

Just send it back, with a note saying it's acting goofy...they will replace it NO CHARGE.

Great Customer Service!!!

Jon

[RogerDat]

Give them a chance to make it right, they have a good reputation for doing just that. And no 171 degrees margin of error is not good. It is enough to have zinc WW's melting in your "700 degree" lead.

[ruizhernandeztrust]

Give them a chance to make it right, they have a good reputation for doing just that. And no 171 degrees margin of error is not good. It is enough to have zinc WW's melting in your "700 degree" lead.

That's my fear, ruin a batch of bullets for not using the correct temperature.

Okay,
I'll contact them, explain the problem and return it.

[Jon K]

I just had one replaced within the last 6 months...had it in 10 days.

Jon

[Doggonekid]

I have been thinking about getting me a temp gage for my casting. When I get one it will be RCBS. I have the RCBS pro melt, it has a gage on it. I have no clue how accurate it is. But I can tell when the lead is too hot and when it to cold. Back to your gage I would call RCBS and send it back I agree with everyone else RCBS will make it right. They are a great company to work with.

[bhn22]

The numbers on the dial are meaningless. They're simply reference points with no correlation to any temperature.

[Mike W1]

I have been thinking about getting me a temp gage for my casting. When I get one it will be RCBS. I have the RCBS pro melt, it has a gage on it. I have no clue how accurate it is. But I can tell when the lead is too hot and when it to cold. Back to your gage I would call RCBS and send it back I agree with everyone else RCBS will make it right. They are a great company to work with.

I'd suggest a thermometer from Brownells. The guarantee is just as good and theirs is adjustable. Frankly having most all this stuff myself I'd suggest a VOM with a thermocouple as being a much better option than a stem thermometer!

[ruizhernandeztrust]

The numbers on the dial are meaningless. They're simply reference points with no correlation to any temperature.

Then what's the point of having a thermometer in the first place if I can't trust these numbers. Now I'm clueless.