What is the tap/thread size for the drop tube? I figure I would try to tap the Ohaus 7200 so I could use the uniflow drop tubes. OR I have a drop tube from a 55 measure I could weld to the bottom of it.
What is the tap/thread size for the drop tube? I figure I would try to tap the Ohaus 7200 so I could use the uniflow drop tubes. OR I have a drop tube from a 55 measure I could weld to the bottom of it.
Last edited by tonyb; 12-08-2014 at 06:30 AM.
___________________
NRA Life Member
10-4 Good Buddy, You got the Duck
What size tap do I need? Please help.
___________________
NRA Life Member
10-4 Good Buddy, You got the Duck
Bayou52
NRA Life Member
"Keep Calm and Reload"
Thanks but I'm going to weld the piece on.
___________________
NRA Life Member
10-4 Good Buddy, You got the Duck
Mine measures(.531-20) 17/32-20, good luck finding a tap.
Calamity Jake
NRA Life Member
SASS 15704
Shoot straight, keepem in the ten ring.
Hi,
Instead of welding on the measure and ruining it,IMO. You could just buy a benchrest kit for it from Sinclair!
http://www.midwayusa.com/find?dimensionids=11908
Last edited by seagiant; 11-25-2014 at 05:40 PM.
“If ye love wealth better than liberty, the tranquility of servitude better than the animating contest of freedom, go home from us in peace.
We ask not your counsels or arms.
Crouch down and lick the hands which feed you.
May your chains set lightly upon you, and may posterity forget that ye were our countrymen.” -Samuel Adams
Janet Reno, killed more children at Waco, with Bill Clinton's permission, than Adam Lanza killed, at Sandy Hook.
My Uniflow drop tube measures .546 (35/64) X 18 tpi. A real oddball size. Finding a correct tap would be quite a challenge. You might get away trying a standard 9/16 (.562) X 18 tap. It might be a little loose, but a RCBS drop tube should thread in tight enough. It would be easier to verify the thread dimensions for your Ohaus, and have a machinist make a proper drop tube up for you.
Email from RCBS says it's a 9/16 x 18.
Thanks everyone
___________________
NRA Life Member
10-4 Good Buddy, You got the Duck
I once made an "adapter" to allow a Uniflow measure to sit in a Lee "through the expander die" so that the powder would drop directly into the neck expanded case. I unscrewed the plastic green drop tube and found that a 9/16x 18 bolt would thread into the (the place of the green drop tube). So I had a machinist friend bore the largest hole possible through the bolt with a taper in it (on the measure end). Of course the bolt head had to be rounded as well to fit into the Lee gizmo that would normally hold a Lee powder powder funnel. It worked. I was able to/can dispense powder directly from the RCBS measure into whichever case I want to charge. If you go this route just be sure that the bolt you work with is not too short...long enough to get the job done, but not excessively long either. LLS
I drilled and tapped the Ohaus 7200 measure, cut off the end flush. Now I can use the Uniflow drop tubes.
33/64 drill bit
9/16 x 18 tap
Last edited by tonyb; 12-08-2014 at 06:26 AM.
___________________
NRA Life Member
10-4 Good Buddy, You got the Duck
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |