RepackboxWidenersSnyders JerkyRotoMetals2
Load DataLee PrecisionInline FabricationTitan Reloading
MidSouth Shooters Supply
Page 1 of 2 12 LastLast
Results 1 to 20 of 30

Thread: where to start

  1. #1
    Boolit Mold
    Join Date
    Jan 2011
    Location
    Lewisburg Ky
    Posts
    14

    where to start

    Well i have been thinking about starting to cast and handload for a couple years now. Have been saving my brass for 4 years now. I really don’t think that is the cost of bullets making me want to do this rather than taking it to the next level with being in control of everything by casting boolits. Don’t get me wrong saving money is always a good thing. I have been watching this board for a while now and now is the time for me to stop being a lurker and step up and join in.

    I plan on reloading my 270, 9mm, 44mag, 45acp and 45acp.

    Started collecting wheel weight about 4 months ago.

    My first question of many that i will have to come in the process of learning. I was planning on slugging my barrels before i even think of buying a mold. Where is a place i can buy the slugs i would need for this process. Do they sell a handful or do you have to buy a bunch of them and how much do you think they will cost.

    The order i am planning on buying my equipment is
    melting pot
    molds
    lube/sizer
    tumbler
    grain scale
    press

    Anything else i should add to the list that is just off the top of my head

    Already have the setup for melting the ww's, flux and lots of reading material.

    Thank you for all the stuff that I have learned from this site already and the help to come.

    Kywilber

    Just wondering anyone from Logan county KY?

  2. #2
    Boolit Buddy bowenrd's Avatar
    Join Date
    Jan 2009
    Location
    TOU (Top of Utah)
    Posts
    132
    buy Lyman's "Cast Bullet Handbook" and read it, read it and read it.

  3. #3
    Boolit Master fryboy's Avatar
    Join Date
    Feb 2010
    Location
    3 1/2 miles out past the stix on the 9.9
    Posts
    2,774
    hola amigo !
    hmmm i mite be tempted to say buy the press and scale first as one can also use them to load umm jacketed bullets , but if you find anything reasonably priced on your list grab it . as for slugging the barrel soft fishing sinkers often work ,split shot or egg type sinkers , just find some a lil bigger than needed , also using a mold with pure lead and perhaps swaging/squishing it a little fatter can be used , one thing i didnt notice on your list was a ingot mold , many things will work for both ingot molds and smelting pots and with a dipper the smelting pot can also be used to cast boolits with , you can also get buy with the lee size dies before you get a lubrisizer and either tumble/pan lube , happy reading amigo there's lots of good information here and quite a few happy to help people

  4. #4
    Boolit Mold
    Join Date
    Jan 2011
    Location
    Lewisburg Ky
    Posts
    14
    Lymans book should be here within a week. Ordered it last friday.
    Forgot ingot molds i got ideas from here and made some out of 1 1/2 angle iron. I want to go bigger but that is what i had in the storage building. I will check the building to see if i have any fishign weights i can use. Very true the lee sizer and pan lubing would be alot cheaper to get started.

    Thank you for the idea's

  5. #5
    Boolit Buddy SkookumJeff's Avatar
    Join Date
    Jan 2011
    Location
    Western Washington
    Posts
    141
    I've been reloading a long time, 30 years. Mostly with jacketed bullets. I know my business when it comes to reloading. I've done some benchrest shooting and built a few accurate rifles/loads. It's not easy to load ammunition that shoots better than premium factory ammo. You really have to know what you're doing.

    I've just started boolit casting and my head is swimming with all the details that need to be understood to be effective. I have some big bore rifles and handguns that are really crying out for lead cast boolits. I plan to hunt with my cast boolits, so they need to be accurate and they need to perform properly.

    I'm helping a buddy get up to speed on reloading. He's one of the sharpest people I know, and he's overwhelmed with all the minutia and detail involved with reloading for jacketed bullets. Once he gets up to speed, I'm gonna pressure him to try some cast boolits, but that's for another day.

    The point is..knowing all that I've learned over thirty years of reloading...and all I've been learning about boolit casting, lead alloys, casting technique, tooling, etc. etc., I would find it really, really hard, to learn how to reload, and learn how to cast boolits, all at the same time. There's so many details with both areas to learn, doing all of it at once would be daunting to say the least, if not counterproductive. I would not be inclined to recommend to any of my buddies to try to do this.

    Am I off base here? I'm not trying to dissuade anyone from casting boolits...I'm just sayin, larnin both at the same time is going to really be hard.

    I'd recommend focusing on reloading first, dare I say it, with jacketed bullets. If shooting cast is that important then buy some cast boolits to reload if you really want to work with cast boolits. But focus on reloading until you get comfortable with the reloading process.

    SkookumJeff
    Last edited by SkookumJeff; 01-10-2011 at 12:52 AM. Reason: Cause I had more to say

  6. #6
    Super Moderator




    Buckshot's Avatar
    Join Date
    Mar 2005
    Location
    So. California
    Posts
    11,833
    Quote Originally Posted by SkookumJeff View Post
    The point is..knowing all that I've learned over thirty years of reloading...and all I've been learning about boolit casting, lead alloys, casting technique, tooling, etc. etc., I would find it really, really hard, to learn how to reload, and learn how to cast boolits, all at the same time. There's so many details with both areas to learn, doing all of it at once would be daunting to say the least, if not counterproductive. I would not be inclined to recommend to any of my buddies to try to do this.

    Am I off base here? I'm not trying to dissuade anyone from casting boolits...I'm just sayin, larnin both at the same time is going to really be hard.
    ...........It might be a bit dissappointing to kywilber, but I do not believe you're off base in your thinking. Plus the fact that jacketed bullets are becoming increasingly dear almost day to day, would be an added impetus to eventually start founding and shooting cast lead. To begin reloading with jacketed first contains all the knowledge needed for eventually substituting cast for jacketed (with a few caveats).

    That is to say, the singular fact of casting lead boolits has nothing to do with the science of reloading ammo. That is to say, fully understanding how to cast an excellent boolit will aid you not in the least, and has bothing to do with reloading. However if a person wanting to learn about reloading started with handgun ammo first, and bought commercial cast boolits, I'd think THAT would be a means to not only get a good handle on reloading, but also at the same time some valuable info with cast boolits.

    .................Buckshot
    Father Grand Caster watches over you my brother. Go now and pour yourself a hot one. May the Sacred Silver Stream be with you always

    Proud former Shooters.Com Cast Bullet alumnus and plank owner.

    "The Republic can survive a Barack Obama, who is, after all, merely a fool. It is less likely to survive a multitude of fools such as those who made him their president."

    Shrink the State End the Fed Balance the budget Make a profit Leave an inheritance

  7. #7
    Boolit Master
    Join Date
    Nov 2009
    Posts
    587
    Do yourself a favor, cast and reload for the 45acp FIRST before you run out and buy all this equipment. It's extremely forgiving and easy to load for, and a good teacher for the other calibers. If you get all the dies, molds and other doodads for all calibers you'll have quite a mess on your hands.

  8. #8
    Moderator Emeritus / Trusted loob groove dealer

    waksupi's Avatar
    Join Date
    Mar 2005
    Location
    Somers, Montana, a quaint little drinking village,with a severe hunting and fishing problem.
    Posts
    19,417
    I'd suggest getting very comfortable with reloading jacketed bullets first. Cast boollits are an advanced art, and you really need a good grasp on the basics.
    The solid soft lead bullet is undoubtably the best and most satisfactory expanding bullet that has ever been designed. It invariably mushrooms perfectly, and never breaks up. With the metal base that is essential for velocities of 2000 f.s. and upwards to protect the naked base, these metal-based soft lead bullets are splendid.
    John Taylor - "African Rifles and Cartridges"

    Forget everything you know about loading jacketed bullets. This is a whole new ball game!


  9. #9
    Boolit Grand Master
    Mk42gunner's Avatar
    Join Date
    Aug 2005
    Location
    Butler, MO
    Posts
    9,101
    There is no doubt that reloading with jacketed bullets is an easier process than with cast. It takes away several variables right from the start.

    I would be inclined to start with your .270. Get a loading manual, a box of 130 grain spire points and can of 4350. Load and fire a few boxes, then start with the handguns.

    Keep it simple starting out, Winchester 231 will do for plinking loads for all the handgun calibers you listed. You won't be able to get top end loads with your .44 Magnum, but you will be learning the correct loading procedures.

    Good Luck,

    Robert

  10. #10
    Boolit Mold
    Join Date
    Jan 2011
    Location
    Lewisburg Ky
    Posts
    14
    Well for the 45acp i was thinking of starting off with

    Lyman 4-Cavity Bullet Mold #452374 45 Caliber (452 Diameter) 225 Grain Round Nose (just becouse the of the design and that is what i shoot currently in my glock 21. Have always found it to be a great ammo for plinking) For the powder was going to start with a good all around w231 using 4.3 grains to start and work my way from there.

    The reason I was planning on waiting on buying the press last is it cost the most. The nice thing about lead is if it is a bad cast or you just don't like it for any reason at all or just want the practice you can remelt it and try again.

  11. #11
    Boolit Master



    Join Date
    Jan 2010
    Location
    Northern Illinois
    Posts
    1,782
    When I started this journey, I got the press first. Then the dies. I loaded for about a year and then decided to cast. I'm glad I went that route. I would recommend buying some lead boolits on line and load them up. Once you get 500 rounds loaded up, you can see if you want to take the next step. IMO
    Have fun! Reloading and casting are great hobbies.
    ARMY Viet-Nam 70-71

  12. #12
    Boolit Mold
    Join Date
    Jan 2011
    Location
    Lewisburg Ky
    Posts
    14
    i was thinking about going with the blue for presses. But as i am going to go with a lee sizer and pan lube to start i will need a single stadge press for that. What is every one thoughts of the Lee Challenger Breech Lock Single Stage Press Anniversary Kit. I do see the point that everyone is making about see if i am going to like reloading before i take the full dive in.

    Kywilber

  13. #13
    Boolit Master



    Join Date
    Jan 2010
    Location
    Northern Illinois
    Posts
    1,782
    That would be a good place to start. I have the Lee Classic Turret press. I also bought the Lee .38-.357 dies for it and was pretty disappointed with them. They worked ok for jacketed but did not work well with my cast. I have a digital scale, Lee press, Lee sizing die, Lyman "M" die, RCBS seating die, and a modified Lee crimping die. I wish I would have gone with either Lyman or RCBS from the get go. There is no problem with going"blue" with all of your stuff if you can afford that route. By getting the Lee single stage press, you will find out that down the line you may want more than one press and the Lee will work whatever route you go.
    ARMY Viet-Nam 70-71

  14. #14
    Boolit Master
    Join Date
    Mar 2007
    Posts
    2,377
    There is some good advice here. Baby steps. I would say get a single stage press first. You can always add a progressive press later. You need to get the basics of reloading down first, before trying to crank out 300 rounds an hour.
    Once you feel comfortable loading add the progressive and move the single stage over for sizing duty.

  15. #15
    Boolit Master jmsj's Avatar
    Join Date
    Nov 2009
    Location
    New Mexico
    Posts
    1,166
    kywilber,
    Welcome to the site.
    I think many here were reloaders first then got into casting, I did. I think that going from a reloader first to being a caster second is a natural progression. I do not think that this is neccesarily mandatory. It would take a lot of study on your part but it is certainly possible.
    If you are going to do both from the start and have no equipment, the Lee kits are attractively priced and do work. I would look at a single stage or turret press and use as the turret press as a single stage to start. The turret head makes swapping calibers nice as they stay together and adjusted as a set. Also I see that you have started to collect scrap lead, you are going to need a smelter set up also.
    Do you have a friend that reloads? If you can, see if someone can walk you through it. That will let you see if this is something you want to try. I am teaching a young man to reload and cast at the present time. Hey I just thought about this, you can check out some youtube videos regarding casting and reloading.

    Regardless which you decide to do, read and study lots and ask questions. This site is great about helping new guys out. For information about casting and lead check out the "stickies" here and check out www.lasc.us There are lot of great articles on both sites.
    Welcome and good luck, jmsj

  16. #16
    Boolit Grand Master

    Wayne Smith's Avatar
    Join Date
    Mar 2005
    Location
    Hampton Roads, Virginia
    Posts
    13,690
    You are starting to climb two very different learning curves. The second, casting, is dependent on and a subset of the first, reloading. Both have significant safety issues and both are very detailed and require significant background knowledge. You won't even know what you don't know until you start. I'm a psychologist, I had to learn basic chemistry and metalurgy to be as successful as I am.

    You can pick up a Lee single stage press for less than $30, I believe. That's where to start. Even when you go to the Dillon, if you ever do, you will have multiple uses for that basic single stage. Just to reload you need the press, the scale, something to hold cases, a powder measure, a powder funnel, case lube, primers, powder, and bullets. I assume you have cases. You will soon need something to pull bullets to fix mistakes.

    I strongly recommend that you climb one learning curve at a time. Reloading wrong can kill you, can destroy guns, and can maim you or others. I don't want to scare you but I do want you to slow down and think through what you want to accomplish and take your time.

    You will make mistakes, God willing you will catch them before they get into your gun. Learn reloading one step at a time, focusing on quality rather than quantity. Once you have mastered this you can think about moving to casting or progressive reloading. You really only need the Dillon (progressive) if you are shooting competitively. You will be suprised at how quickly you can reload with a single stage. When you make a mistake it does not affect the whole batch - just the ones you made before you caught yourself.
    Wayne the Shrink

    There is no 'right' that requires me to work for you or you to work for me!

  17. #17
    Boolit Bub
    Join Date
    Jan 2010
    Location
    Northwest IN
    Posts
    60
    +1 on going slow and learning reloading first.

    It's not so hard you can't figure it all out, but it is so important you don't want to mess it up! Kind of like aviation...

    I built up first rate equipment, all at a pretty good deal. I've learned to load on a 550 for .45, and cast for it too. learning rifle now on 223. I'm learning and playing as I have time, but still faster than my wife thinks is needed...

    Buy once, cry once is something you'll hear a lot of on this board. Watch craigslist, ebay, forum classifieds, etc and buy the better tools as you have the money. You'll have plenty to keep you busy in the shop.

    Most of all, don't forget to go shooting!


    Andy

  18. #18
    Boolit Master




    Cherokee's Avatar
    Join Date
    Aug 2005
    Location
    Medina, Ohio
    Posts
    2,227
    Welcome to the forun. When I got started over 50 years ago, I bought used equipment. I startred slow with jacketed bullets in 30/06 & 30 Carbine, then 38/357, 45 ACP. Then I started buying cast bullets for the pistol rounds. A couple years later I started casting some bullets myself, again buying a used sizer but new molds. CB's quickly replaced jacketed in the handguns. Over the years I have upgraded equipment as needed and any replaced equipment went to another reloader for his use. Just my experience.
    God Bless America
    US Army, NRA Patron, TSRA Life
    SASS, Ruger & Marlin accumulator

  19. #19
    Boolit Master
    Join Date
    Mar 2009
    Posts
    4,116
    I agree that learning the basic princilpes and mechanics of reloading, prior to learning casting, is the best approach. Learning the quirks of both at the same time offers too many opportunities to get frustrated or fail.

    Keep it simple, too, by buying basic, used equipment or a Lee kit...it can always be used to augment your final setup.

  20. #20
    Boolit Master




    Echo's Avatar
    Join Date
    May 2008
    Location
    Tucson AZ
    Posts
    4,604
    Quote Originally Posted by Buckshot View Post
    ...........It might be a bit dissappointing to kywilber, but I do not believe you're off base in your thinking. Plus the fact that jacketed bullets are becoming increasingly dear almost day to day, would be an added impetus to eventually start founding and shooting cast lead. To begin reloading with jacketed first contains all the knowledge needed for eventually substituting cast for jacketed (with a few caveats).

    That is to say, the singular fact of casting lead boolits has nothing to do with the science of reloading ammo. That is to say, fully understanding how to cast an excellent boolit will aid you not in the least, and has nothing to do with reloading. However if a person wanting to learn about reloading started with handgun ammo first, and bought commercial cast boolits, I'd think THAT would be a means to not only get a good handle on reloading, but also at the same time some valuable info with cast boolits.

    .................Buckshot
    Plus one. Once you are comfortable with the process of reloading (using purchased cast boolets, for your .45's), and condom bullets for your long guns, then you could engage the new process of casting boolets for both - and find new areas of confusion and exasperation!
    Echo
    USAF Ret
    DPS, 2600
    NRA Benefactor
    O&U
    One of the most endearing sights in the world is the vision of a naked good-looking woman leaving the bedroom to make breakfast. Bolivar Shagnasty (I believe that Lazarus Long also said it, but I can't find any record of it.)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check