Yup, that's the question . I'm looking for load data with Unique, 800X , HS6/540 and Universal.
Any help will be GREATLY Appreciated!!!!
Thank you .
Glen.
Yup, that's the question . I'm looking for load data with Unique, 800X , HS6/540 and Universal.
Any help will be GREATLY Appreciated!!!!
Thank you .
Glen.
You are being watched.
http://www.hodgdonreloading.com/data/pistol
Hope this helps
The fear of the Lord is the beginning of knowledge: but fools despise wisdom and instruction.
Proverbs 1:7
I was hoping for someone's thread on here. I've looked for load data on here but must be doing something wrong and can't find the page.
The Hodgdon site has , full house loads. Which I already have . I'm trying to find the 800-1000 fps loads with Unique, ECT.
Thanks.
You are being watched.
I just got in from shooting my .480 SBH. My reduced power load is 10.5 Gr. HS-6 and the 400 gr Lee. I haven't ran it across the chrono yet. Should be about 1000 fps. For full throttle loads I've been shooting 20 gr. AA#9s with the same Lee 400 should be about 1200 fps. I've only got a couple of hundred rounds threw the gun so just getting settled in but this is working good so far.
Awesome. Thank you. I have a Lee 476- 400 gr mold also . And a friend has a pound of Win 540 he will sell me. Its a Long way to the powder store.
How does the plain base 400 gr8 boolit do with 20 gr of #9 ?
What bhn is your boolit ?
Last edited by Cold Trigger Finger; 08-06-2017 at 09:10 PM.
You are being watched.
In both loads I've been shooting the same 400 gr. lee boolit. Water quenched clip on WW, BAC Lubed and sized to .476. The 20.0 gr. #9s load is safe in my gun. I did have to install a taller front sight but No pressure signs. Really the 1000 fps HS-6 load is more than enough for anything until I get back up to your neck of the woods.
On a side note I purchased an Alaskan chest holster made in Wasilla for this .480 Bisley 6.5" SBH. Spendy but very high quality.
I have a load with an Accurate Molds 380V pushed by 21 gr Accurate #9 in my 7 1/2" SRH. Its a good load going 1300 fps. The lower velocity loads will be fun to shoot. Where did you get the taller front sight. I need one Also. And one for my 45 Bisley Blackhawk.
Have you done any longer range shooting with the Lee 400gr . . I haven't cast with mine yet, but it looks like a good looking boolit . Like a LFN design.
I make most of my own holsters. Rough out. Full flap. Integral belt loop. Lots of years falling timber and thinning trees got me hooked on full flaps. They had something figured out in the Civil War as far as holsters go.
Last edited by Cold Trigger Finger; 08-07-2017 at 12:42 AM.
You are being watched.
Try this thread. I am also looking to lighten up my 480 loads but I don't have any empties and they go through my stop. I will be building a thicker stop to allow me to capture the lead after I tear this one apart and mine the spent lead from it.
http://castboolits.gunloads.com/show...feed-480-Ruger
for the Ruger 480, I'd start with 9gr of Unique and work up.
I have only loaded the Ruger 480 with jacketed to factory specs, but I have tried Unique in the larger but similar S&W500.
I posted a little bit about it, in this thread.
http://castboolits.gunloads.com/show...he-500-S-amp-W
~~~~~~~~~~~~~~
“If someone has a gun and is trying to kill you, it would be reasonable to shoot back with your own gun.”
― The Dalai Lama, Seattle Times, May 2001
I found some lighter bullet loads on Alliante's web site. . I sent a question about safe starting loads with Unique and 410 gr cast in the 480.
If they reply I'll update this thread.
You are being watched.
Hodgdon has a listing for Titegroup.. in the 8 gr range for a 420 gr bullet barely making 958 fps and 10.7 gr with the lightest 325 gr bullet at 1158 fps. I prefer titegroup over most other powders since it proved to me to be temp and position insensitive when I was working up mouse far loads in the smaller 41 magnum case.. I've found Unique to be inconsistent depending on position in the case where there was lots of room inside.
Ok. Thanks. I think I have some of it.
You are being watched.
45 COLT data.
?? If you had a link with your post , it didn't come thru.
You are being watched.
Found this on Shooters Forum. EVERYWHERE
AND SHOW ME
POSTS
THREADS
Index
Handguns Category
Handgun Cartridges
JimC
May 30, 2004 · #1
Unique for .480 Ruger
I have a SRH Ruger .480, 7.5" barrel. I thought I would try some Unique behind 355 gr. BTB. I couldn't find any data for the .480 with Unique so I started with 11 grains and then worked up to 12.5 grains of Unique. Does this sound reasonable? Has anybody used Unique with the .480 Ruger?
I shot it for the first time this week. I shot 26 grains of H110 behind a BTB 355gr GC. Serious recoil! The very first thing I'm going to do is send this baby of to be MagNaPorted and change to Pachmeyr decelator grips and wear a glove!!
My middle finger touches the trigger guard-it's still swollen!
Love that Ruger!
JimC
Wyogoose
R. S. Wyo
May 30, 2004 · #2
480 ruger
I have the taurus 5" with the porting 325 XTP 27 GR 110 WLP,
Cast Performance (sorry Marshall!?!) 375 LFNGC 20 gr. 2400 WLP, and 405 self cast Lee mold 18 gr 2400 WLP and realize amazing accuracy and very tolerable recoil. The grips are factoy and have a pad (sorbathane????) in the back strap that really make it a ***** cat considering what it is doing. My buddies and I all agree most 44's seam to be more punishing. I wanted the Ruger but run into a steal on the Taurus. After reading everyone complain about the recoil with the SRH I am thinking it was a better deal than thought.
axlenut
San Francisco Bay Area
May 31, 2004 · #3
JimC said:
I have a SRH Ruger .480, 7.5" barrel. I thought I would try some Unique behind 355 gr. BTB. I couldn't find any data for the .480 with Unique so I started with 11 grains and then worked up to 12.5 grains of Unique. Does this sound reasonable? Has anybody used Unique with the .480 Ruger?
I shot it for the first time this week. I shot 26 grains of H110 behind a BTB 355gr GC. Serious recoil! The very first thing I'm going to do is send this baby of to be MagNaPorted and change to Pachmeyr decelator grips and wear a glove!!
My middle finger touches the trigger guard-it's still swollen!
Love that Ruger!
JimC
Jim:
I shoot the Ruger SRH 7.5" and a Gary Reeder Ultimate .480 Custom 5 shot rebuild of a Ruger Blackhawk. Neither really liked Unique. !0.0 grains of Unique was about the best.
This cartridge does best at near max. But I found the following loads a bit milder and still capable of good accuracy with enough power to handle most hunting chores.
Hornady 400 grain XTP bullet with 18.6 grains of Hodgdon Lil' Gun, Winchester LP primer. Average velocity is 1105 fps and 100 yard energy is 914 ft lbs (10 shots). Blue target photo below. 1.25" group at 25 yards.
The best cast bullet load I found was the CPBC 370 grain LFN PB bullet over 25.5 grains of Win. 296 with the WLP primer. This load's average velocity is 1342 fps. with 100 yard energy 1104 ft lbs (10 shots). Red dot target below. .75" group at 25 yards discounting the flyer from broken scope.
You are correct, a shooting glove is needed for the SRH, my middle finger took a beating. Recoil also disassembled the Burris 2x Posi-lock scope which caused that flier in the second photo. The windage turret unscrewed. The Ultimate .480 was made with a Super Blackhawk triger guard and fits my big paw better.
axlenut
Attachments
Post Edited
Last edited by axlenut - May 31, 2004
JimC
May 31, 2004 · #4
Thanks Axlenut for the info. I keep hearing about LilGun, people seem to like it. I have some of those 370 gr plain base cast bullets. I'll try that load you suggest with W296. I don't think I can do anything about the trigger guard other than changing to a blackhawk. I'm sending this thing off for a Mag-Na-Port tomorrow!! That should help.
Thanks,
JimC
JimC
May 31, 2004 · #5
Wyogoose said:
I have the taurus 5" with the porting 325 XTP 27 GR 110 WLP,
Cast Performance (sorry Marshall!?!) 375 LFNGC 20 gr. 2400 WLP, and 405 self cast Lee mold 18 gr 2400 WLP and realize amazing accuracy and very tolerable recoil. The grips are factoy and have a pad (sorbathane????) in the back strap that really make it a ***** cat considering what it is doing. My buddies and I all agree most 44's seam to be more punishing. I wanted the Ruger but run into a steal on the Taurus. After reading everyone complain about the recoil with the SRH I am thinking it was a better deal than thought.
Thanks for the reply Wyogoose,
I also have a Dan Wesson 44 mag, 8.5", that doesn't bother me. This ruger .480 hurts, way more recoil than my Dan Wesson. But I like the gun, it's accurate and it shoots big bullets, just what I like. And I am going to work on the recoil issue, hopefully with good success.
Thanks,
JimC
jcdflint
May 31, 2004 · #6
[QUOTE=JimC]I have a SRH Ruger .480, 7.5" barrel. I thought I would try some Unique behind 355 gr. BTB. I couldn't find any data for the .480 with Unique so I started with 11 grains and then worked up to 12.5 grains of Unique. Does this sound reasonable? Has anybody used Unique with the .480 Ruger?
I shot it for the first time this week. I shot 26 grains of H110 behind a BTB 355gr GC. Serious recoil! The very first thing I'm going to do is send this baby of to be MagNaPorted and change to Pachmeyr decelator grips and wear a glove!!
My middle finger touches the trigger guard-it's still swollen!
Love that Ruger!
JimC[/QUOTE
TRY THIS LOAD!!!! Mild!!! I shoot 16.0 gr. of H110. under 400 gr. Lee Cast bullet at around 950fps out of a 10 inch TC Encore. With My 2 X Burris I can do a 1.20 inch group at 75 yards. Not bad in my books. I think it will make a great deer round!!!! The lee 400 has a very wide flat point. I go up to 22 gr. of H110 if I want a real "BOOMER" But not often!!!!, Jeff
jcdflint
May 31, 2004 · #7
lee 400 gr. 16 gr. H110 PHOTO
PHOTO of load[QUOTE=jcdflint]PHOTO OF LOADOriginally Posted by JimC
Attachments
Wyogoose
R. S. Wyo
May 31, 2004 · #8
H-110
How was the velocity spread with the 16gr H-110. My books (Hornady & Hodgdon) show 17.4 and 18 to be the starters and have heard terrible things about low pressure H-110 and W-296 powders (some say 3% some 10% below printed data) . That is why I went with the 2400 for the lighter load behind the Lee mold. Pretty impressive performance with that bullet for a slow mover, going to try the H-110 with a little more pep as sone as I can get more shipped in.
Post Edited
Last edited by Wyogoose - May 31, 2004
JimC
May 31, 2004 · #9
jcdflint said:
PHOTO of load
PHOTO OF LOAD
That's a light load of H110, most say don't use light loads of H110. I'll try a couple to see what happens. Have you used 4227, I hear it works well fore lighter loads.
Thanks,
JimC
axlenut
San Francisco Bay Area
May 31, 2004 · #10
JimC said:
That's a light load of H110, most say don't use light loads of H110. I'll try a couple to see what happens. Have you used 4227, I hear it works well fore lighter loads.
Thanks,
JimC
They are correct, too light a load of H110 or Win. 296 or AA #9 can cause hangfires and/or high pressures. IMR4227 and the seldom mentioned AA1680 are choices.
The 370 grain CPBC LFN PB over 25.5 grains of AA1680 developed 1108 fps average velocity with a S.D. of 15. Recoil was moderate. Picture on left with no red dot.
The same bullet with 24.0 grains of IMR 4227 produces an average velocity of 1176 fps, but with a spread of 214 fps for a S.D. of 60, but a group of 1.25" at 25 yds. The red dot target in the middle.
Here's where it gets interesting. Increase the load above to 24.5 grains of IMR4227 and the average velocity increases to 1233 fps. the extreme spread drops to 38 fps. and the S.D. drops to 13, while the group size grows to 1.75". The target on the right.
The case won't hold much more IMR4227, but some day I will try H4227 to see if it follows suit. There are some good results with the 400 grain LFN PB and AA1680, but that's for another day.
axlenut
Attachments
3
Show these thumbnails
JimC
May 31, 2004 · #11
axlenut said:
They are correct, too light a load of H110 or Win. 296 or AA #9 can cause hangfires and/or high pressures. IMR4227 and the seldom mentioned AA1680 are choices.
The 370 grain CPBC LFN PB over 25.5 grains of AA1680 developed 1108 fps average velocity with a S.D. of 15. Recoil was moderate. Picture on left with no red dot.
The same bullet with 24.0 grains of IMR 4227 produces an average velocity of 1176 fps, but with a spread of 214 fps for a S.D. of 60, but a group of 1.25" at 25 yds. The red dot target in the middle.
Here's where it gets interesting. Increase the load above to 24.5 grains of IMR4227 and the average velocity increases to 1233 fps. the extreme spread drops to 38 fps. and the S.D. drops to 13, while the group size grows to 1.75". The target on the right.
The case won't hold much more IMR4227, but some day I will try H4227 to see if it follows suit. There are some good results with the 400 grain LFN PB and AA1680, but that's for another day.
axlenut
Thanks Axlenut for the information,
Good shootin'. It's like John Linebaugh says, "there is a specific bullet and a specific powder that is going to work best in your gun, everything is going to be balanced. It's your job to find it. It's obvious you've been shooting that .480 for some time, I'm just starting my adventure with the .480 but the information you give is a great help. What kind of groups do you shoot at 50 and 100 yds?
I'm sending my .480 off tomorrow for a Mag-Na-Port job, when it gets back I'll let you know if it was worth it.
Thanks,
JimC
axlenut
San Francisco Bay Area
Jun 01, 2004 · #12
JimC said:
Thanks Axlenut for the information,
JimC
You are welcome.
I dug up an article by John Taffin from the January 2004 Guns Magazine on reduced loads for big bore pistols. For the .480 Ruger he recommends:
370 Grain Cast Performance Bullet Co. LFN PB, CCI 300 primers, Hornady Brass. Fired in Freedom Arms 4.75" revolver.
Unique 8.0 to 10.0 grains
HS-6 10.0 to 12.0 grains
Universal 7.0 to 10.0 grains
WW231 8.0 to 10.0 grains
He cautioned against increasing the loads. Groups ran from 1.125" to 1.75" at 25 yards.
You are being watched.
http://www.handloads.com/loaddata/ta...Powder&Source=
I like 8 to 9 grains of 231 with a 370 grain bullet. I loaded some last week with 8.5 grains 231 but haven't shot them yet.
Also 16 - 17 grains H108 and the 370 rnfp.
14 - 15 grains Blue Dot with the Mihec 385 gr hp for a hunting load.
http://handloads.com/loaddata/taffin...=Powder&Source
There's some lighter loads here.
Here's a link to a thread on the Single Actions forum; go to page 4 for the .480 data. There are several fairly moderate loads listed there.
http://singleactions.proboards.com/t...ey-chart-added
Service members, veterans and those concerned about their mental health can call the Veterans Crisis Line to speak to trained professionals. To talk to someone, call 1-800-273-8255 and Press 1, send a text message to 838255 or chat at VeteransCrisisLine.net/Chat.
If you or someone you know might be at risk of suicide, there is help. Call the National Suicide Prevention Lifeline at 1-800-273-8255, text a crisis counselor at 741741 or visit suicidepreventionlifeline.org.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |