Yesterday after work I was able to cast for about 2 hours....not sure how many rounds I completed but I used up 17 ingots worth of lead. So all in all a good day!
Maybe I can get them all powder coated today?
Yesterday after work I was able to cast for about 2 hours....not sure how many rounds I completed but I used up 17 ingots worth of lead. So all in all a good day!
Maybe I can get them all powder coated today?
"Yes or no will almost always suffice as the answer"
The weather is changing...I'm aching all over cuz the rain is coming, so...I'm too braindead today to trust myself on one of the presses!
What to do? Just size and powder coat today...simple enough...I can't blow myself up too bad doing that huh?
Attachment 195682
But...As an example of thermometers, we're always talking about verifying your thermometer? Well, I've been using the one in the bottom (previously verified by my electronic Harbor Freight Piece of Spit) and just as a double check on it I put a verified (in the wife's digital oven) thermometer in with it (upper right)...look what a lier that bottom one is!
When it cools down, it's going to meet Mr. Hammer today!
Attachment 195683
a m e r i c a n p r a v d a
Be a Patriot . . . expose their lies!
“In a time of deceit, telling the truth is a revolutionary act.” G. Orwell
Made more lube this morning. A modified Darr lube. Made enough to refill the 450 a couple more times after I use what's in it now.
Tried out one of my Christmas gift moulds , a nifty NOE 41 magnum full wadcutter ,based on the old Lyman 358432 design, looks just like it and weighs 215 grains. With a 50/50 alloy of COWW/ lead they drop at .4125 , right on the money!
I was just heat cycling it for the first time and couldn't resist casting a few.
NOE's are so nice looking I just hate to muck them up...but they are made to cast boolits with.
Gary
Certified Cajun
Proud Member of The Basket of Deplorables
" Let's Go Brandon !"
Formed 53 44x1.6" cases from RP 30-06 and made a decapping stem for a shortened 444 die. Started off with 55 cases but the bandsaw ate one and one ended up too short when the stop collar slipped on the trimmer. Decapping stem is some 3/4" scrap knurled and threaded, with a section of a big nail for the shaft topped off with a loctited in decapping pin. When the pin breaks (and it will) you just heat it up to tap out the old pin and install a new one.
Is that inside neck turning I am seeing? ( hard to tell on the phone )
I managed to find the time to cast 200+ ball for the BP pistols.
Finished the AR so back to reloading. Got some red&blue 176 gr .310 and some 3031 to put in the 30-30.
Sized and primed 200+ 7.62x54 for the Mosin, loading later this week, considering casting for it as well.
Sent from my SM-G935V using Tapatalk
Cast 20 pounds of 360-640 in 50/50 Pb/COWW with a little tin. Maths hints towards 1000 boolits. I'm kind of sore now.
WHEN IN DOUBT, USE MORE CLOUT!
This afternoon will be trim 243 brass for Wyoming next month. Actually 3 weeks.
Bagged up, in 100pcs per bag, a bunch of 223 rounds I have been loading for the past week of evenings. I will be tumbling more this week and sizing them getting ready for more shooting.
I had to make up more 44 mag wood bee loads. We have a bumper crop this year.
Happy day! I got in an order of 7 molds from Magma this morning, which means I can use them this weekend. I just washed them in hot water with soap and water and scrubbed them with a toothbrush. These were the 4 105 grain .38 TC molds and the 3 200 grain RNFP .45 Long Colt molds (I already had one of these molds, so I have 4 now).
I dried them with paper towels and will let them dry over night and then swap in the .38 molds with 4 other smaller weight molds and run a mixture of bullets tomorrow.
I do love running the old Bullet Master!!
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |