Now that you opened the can of worms... Here is a thread about casting for 7.62x25: https://castboolits.gunloads.com/sho...-62x25-Tokerev
Now that you opened the can of worms... Here is a thread about casting for 7.62x25: https://castboolits.gunloads.com/sho...-62x25-Tokerev
NRA Certified Instructor Pistol
NRA Certified Instructor Metallic Cartridge Reloading
NRA Certified Instructor Shotshell Reloading
NRA Certified Chief Range Safety Officer
NRA Life member
www.primercatcher.com
I think this is the best advice you got so far.
While Lyman's castbullet handbook 4th Ed is an excellent reloading manual for cast boolits, You don't need it yet. Just look for a good reloading manual, I do prefer the ones put out by Lyman (they are currently at the 50th edition, I believe)...but if you come across any of the older ones, they will do just fine...But there are a ton of other ones, put up by equipment manufacturers as well as bullet manufacturers.
Also, keep reading here on castboolits...lots of info here.
~~~~~~~~~~~~~~
“If someone has a gun and is trying to kill you, it would be reasonable to shoot back with your own gun.”
― The Dalai Lama, Seattle Times, May 2001
I'd recommend: https://www.starlinebrass.com/762x25-tokarev-brass
For starters, this is the easiest brass to load. It's also the premium handgun brass available.
Read the manuals but, collect the components to start reloading. Yes, I have Lyman books, RCBS equipment like the guys say. Never had an "ammo shortage " yet. I have 3 9mms, 41 mag, and 45 Colt. You get the idea.
Gather your cases, primers, powder and bullets. It's quite the mail order adventure in some respects.
Good Luck,
Ron
In all, the .41 Magnum would be one of my top choices for an all-around handgun if I were allowed to have only one. - Bart Skelton
Post your location and see if someone is close enough to act as a mentor.
[The Montana Gianni] Front sight and squeeze
good evening Buck. welcome to the best web site on the big inner web. Gee, I've looked at the great responses to your initial post, and they are all good. so I won't say any more since I'd just be repeating what has been said. I wish you the best of success in this great hobby.
Mark 5:34 And He said to her (Jesus speaking), "Daughter, your faith has made you well. Go in peace and be healed of your affliction."
This is what I bought ...... twice.
https://www.midwayusa.com/product/1023389781?pid=345426
Mal
Mal Paso means Bad Pass, just so you know.
Lots of good advice here.
I have been casting and reloading for over 40 years and have only blown up 2 guns in all those years.
SAFETY AND PAYING ATTENTION IS PARAMOUNT!
Read up on casting and read up on reloading. YouTube videos abound.
Start with a single stage press. Buy a used RCBS Rock Chucker.
Start reloading ONLY. Casting can wait until you master reloading. That will take you a while. Start with all jacketed bullets until you get the hang of reloading. THEN buy cast lead and see if you like loading lead bullets.
If you cast you will suddenly discover that you can load for a lot less money, which means you load more which means you shoot more which means you cast more, which means you load more......etc. etc.
The you discover that you want to cast for all your guns. So you get more moulds. Then you need reloading dies of course.
Then productivity gets to be more important. So you get a Star Sizer.
Because you are now shooting more, now you need to load more. A single stage might get you 50 an hour if you are lucky.
You spring for a Dillon 550 progressive press that can put out 400 per hour at a leisurely pace.....remember that safety and attention thing.
Then you start being a brass and lead scrounger.
Casting forces you to learn about the metallurgy of lead. You get so desperate for lead that you start mining the berm at your local range.
Are you SURE you want to do this?
I would say absolutely do it. It is a great hobby.
It has become a way for me to relax and do something very productive. My other half calls it "man knitting".
Last edited by FISH4BUGS; 11-30-2021 at 10:17 PM.
Collector and shooter of guns and other items that require a tax stamp, Lead and brass scrounger. Never too much brass, lead or components in inventory! Always looking to win beauty contests with my reloads.
Thanks everyone, I appreciate all the advice! I have a better idea of where to start now. So casting will have to wait, and I’ll get some books and a reloading kit to start out. Does anyone have advice regarding brand or specific kit? I was think of a Lee single stage kit because it was affordable, but I saw several posts mentioning the Rock Chucker kit. Is it better to get one over the other? Or should I avoid kits entirely and piece everything together myself?
Also, thanks to all the people that mentioned Tokarev casting and books for casting. I’m bookmarking a lot of info so I can reference it in the future if reloading goes well.
Edit: I’ve also added my location!
Last edited by Buck Thompson; 12-02-2021 at 02:15 AM.
Ok, so you are new to reloading & all. LOTS of good advice in these 2 pages.
There's a saying; "Buy once,, cry once." If you are trying to be frugal,, then hunt for the Rockchucker and other things on the used market. You can save money if you shop around & all. BUT,, you can also do good by getting a"kit" to get started,, as it'll have much of the stuff you need.
I've been handloading since the mid 1970's,, and I still have my first Rockchucker press,,, and several die sets from back then. While Lee is good,, overall,, you'll find the RCBS Rockchucker will outlast you AND retain value better.
And reloading books are a NECESSITY!
Basic necessities;
2-3 GOOD reloading manuals
Press,
Dies w/ shellholder (Carbide if possible,)
scales,
powder measure
Loading tray
PATIENCE!
Once you get comfortable reloading,, and such,,,, then you can start acquiring the stuff necessary to start casting to start another level of enjoyment.
You failed to mention one other thing that is needed and that is a good dose of common sense. Think about what you are doing while you are doing it.
Other things that you need to know and don't have to buy:
If you smoke don't while doing any of the reloading procedures that involve gun powder or lead and don't get distracted. Tell the wife and kids that you are reloading and not to disturb you. TURN OFF YOUR PHONE. Distractions can cause squibs and double charges.
A vote for anyone other then the conservative candidates is a vote for the liberal candidates.
It is easy to do. Both guns I blew up were double charged 9mm.
How?
They turned out to be military cases and the primer wouldn't seat properly.
Rather than clear the press, i absent mindedly yanked the military case from station 1 (Dillon 550) and just replaced it with a new case.
Station 2 got another charge.
BOOM! The 3914 bent the slide out and totaled the gun.
The S&W 76 was built like a tank and only blew the face of the bolt off.
Now, if ANYTHING goes wrong, I clear the press before fixing it.
Being safe and always paying attention is rule #1!!!!!!!
Collector and shooter of guns and other items that require a tax stamp, Lead and brass scrounger. Never too much brass, lead or components in inventory! Always looking to win beauty contests with my reloads.
When I started buying reloading equipment my first press was a used RCBS Jr. 2 which I still have. It’s adequate for most reloading tasks. Later I got a Rock Chucker and it’s my primary single stage press. If I had to start over I would most likely get the Lee Classic Cast because of its spent primer handling. Any of the above, used or new, will serve you well.
Look at the currently available Rock Chucker kit for ideas for the rest of the early hardware needs.
Sometimes life taps you on the shoulder and reminds you it's a one way street. Jim Morris
Start with a kit . Get the best you can afford but don't break the bank ... as you gain experience you upgrade the things you feel are lacking .
Most of us started out with Lee Classic Loader ( Whack-A-Mole) kit ... the hammering gets old .
There is nothing wrong with Lee Equiptment , it's affordable and will get the job done .
If you don't have a place to mount a press ... the Lee Hand Press or better yet the Buchanan Hand Press , made and sold by a fellow member , www.buchananprecisionmachine.com , are wonderful for loading sans hammer and bench mounted press .
A lot of my "stuff" came from Lee and there is only one item I'm not crazy about ... their new hand priming tool with the folding tray .
I do all my handgun and 30-30 rifle with a Hand Press ... a Lee Hand Press Kit , set of dies and a powder scale (balance beam is my preference) and you have all the tools . A powder measure can come later ... I still scoop a lot of charges with a powder scoop ...easier to do .
Gary
Last edited by gwpercle; 12-03-2021 at 10:36 AM.
Certified Cajun
Proud Member of The Basket of Deplorables
" Let's Go Brandon !"
I saved a lot of money buying good used reloading equipment on this forum and few others.
Used presses at a cost savings you can’t go wrong.
Hand tools and cartridge prep stuff mostly used again good savings.
As far as tumbler and brass cleaning equipment you can clean in a bucket with dish soap and lemi- shine or find a used or cheep harbor freight tumbler for brass cleaning, lots of guys wet to wet tumble and sell off their vibrating tumblers cheep.
Good luck, be safe and NEVER RUSH when reloading !!
Mike
My Feed back link http://castboolits.gunloads.com/show...-myg30-GOODGUY
You are on the right track going to handloading first, then go to casting second.
A good single stage press is the foundation to start with.
If you can score a good price on a starter kit with a RCBS Rock Chucker, that’s great, but pieces here and there is good so long as you get a good deal.
I like the Classic Cast series of presses that Lee now produce as well.
If you go with a kit I would go RCBS or Hornady due to their scales and powder measures.
Separately, the Lee Classic Cast does a better job with spent primers. Then go RCBS Uniflow for a measure.
Scale wise I like mechanical better than electronic. If you can score one, the RCBS 510 or 1010 are held in high regard. I have both but then fell into the grand RCBS 304 dial a grain, color me a snob!
Case trimmers are many, I like the Lyman Universal with a carbide cutter. My varmint rounds get the Wilson trimmer for their final run.
The CZ 52 and the 7.62 x 25mm is not the easiest critter to start with but not truly difficult. They give you great exercise chasing cases. The Wolf extra power spring tamed my pistol down some in that regard.
A big welcome to “Boolits”
Three44s
Quote Originally Posted by Bret4207
“There is more to this than dumping lead in a hole.”
Read this section of the forum and you might find some really good ideas:
https://castboolits.gunloads.com/for...-Helping-Hands
Start with this thread and then go to page one of Helping Hands:
Or you could read a few more of Cag's StudentoftheBoolit threads for a quick overview of the new guy learning procedure and then on to Helping Hands page one.
https://castboolits.gunloads.com/sho...lit&highlight=
You'll have to copy and paste this link as it doesn't automatically highlight as a link. Never mind. The link does work!
I was remiss in my earlier post!
The very first step is to acquire and read a collection of reloading manuals!
Safety first!
Three44s
Quote Originally Posted by Bret4207
“There is more to this than dumping lead in a hole.”
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |