SO, I REMEMBER SEEING A POST ON THE CORRECT SIZER USED FOR REVOLVER BULLETS BASED ON THE CYLINDER THROAT DIA., BUT I CANT FIND IT.
i MEASURED EACH CHAMBER, 2 @ .356, AND THE OTHER 4 AT .357.
WHAT SIZE SHOULD I SIZE THE CAST BOOLITS?
SO, I REMEMBER SEEING A POST ON THE CORRECT SIZER USED FOR REVOLVER BULLETS BASED ON THE CYLINDER THROAT DIA., BUT I CANT FIND IT.
i MEASURED EACH CHAMBER, 2 @ .356, AND THE OTHER 4 AT .357.
WHAT SIZE SHOULD I SIZE THE CAST BOOLITS?
Contact member DougGuy and have him hone your chamber throats to .3585". The chamber throats need to be at least as large as your groove diameter.
Service members, veterans and those concerned about their mental health can call the Veterans Crisis Line to speak to trained professionals. To talk to someone, call 1-800-273-8255 and Press 1, send a text message to 838255 or chat at VeteransCrisisLine.net/Chat.
If you or someone you know might be at risk of suicide, there is help. Call the National Suicide Prevention Lifeline at 1-800-273-8255, text a crisis counselor at 741741 or visit suicidepreventionlifeline.org.
EVERY GOOD SHOOTER NEEDS TO BE A HANDLOADER.
NRA Cert. Inst. Met. Reloading & Basic Pistol
I've had a Ruger Blackhawk 357 magnum since 1970 , the Lyman manual at that time instructed to size them .357" which I did for 40 years .
Tried .358" a couple years ago and the accuracy is the same ...5 shots touching and 1 shot 1/4" away from the rest ... there always seems to be one .
I might be tempted to leave the 4 throats at .357" and have the other two reamed to .357" to match ... but ask DougGuy what would be proper ...he's the expert...
... hole reamer
Gary
Certified Cajun
Proud Member of The Basket of Deplorables
" Let's Go Brandon !"
I had Doug work my 45lc Blackhawk. Highly recommend his work
I Am Descended From Men Who Would Not Be Ruled
Fiat Justitia, Ruat Caelum
There is enough fat in the federal government that if you rendered it you could wash the world
Ronald Reagan.
How did you measure your chambers?
I guess my question is, are you confident in your measurement?
Not to discourage having work done, but if you have a sizer it is simpler to just size a bullet and see if it goes through the chambers. Then you will know for sure if your measurements are right and if you need to spend effort having the gun worked on.
Hick: Iron sights!
Not to overcomplicate the issue, but before starting work on the cylinder, I would start by checking for frame crush first, and work backwards from there.
You can check this with pin gauges. If the bore diameter of your barrel will allow - for example - a maximum of .346" or .347" pin gauge to start down the muzzle, but it won't push past or gets tighter at the junction of frame and barrel, then you have probably .001" to .002" of compression from when your barrel was screwed in under force. This can cause leading if your bullets can't obturate back up to the correct diameter of the rest of the bore.
Look up some of our threads on fire-lapping your barrel with grit impregnated bullets. This will hone out your frame crush, and if you're clever enough to only shoot your lapping bullets out of your tighter chamber throats, you can possibly bring those up to the same spec as the rest.
But once any frame crush is gone, you can properly slug your bore for groove diameter, and make determinations on what your cylinder may need from there. Odds are you have a .357" groove, will ultimately want .358" bullets, and a baaaaaaarely larger than .358" cylinder throat.
Basically, start with the barrel and work from there.
WWJMBD?
In the Land of Oz, we cast with wheel weight and 2% Tin, Man.
If you are going to make a hole in something. MAKE IT A BIG ONE!
In addition to the thread choke there can also be a restriction along where all the warnings and info is stamped/roll pressed into the barrel. I found this in my 80's RedHawk and Ruger Speed Six using pin gauges. As mentioned, a proper fire lapping regime can fix a lot.
I bought manuals/components from both NECO Pressure(fire) Lapping https://www.neconos.com/category/PRESSUREFIRELAPPING-20 and Beartooth Bullets, Technical Guide, A Comprehensive Guide for Unsurpassed Performance Using Cast Bullets by J. Marshall Stanton. Marshall Stanton's book is a genuine treasure to me. Unfortunately Beartooth Bullets and Marshall Stanton seem to have sailed into the sunset.
edit: there is a Beartooth Bullets Technical Guide listed on Fleabay for about twice what I paid ten years ago.
Last edited by oley55; 09-12-2023 at 08:20 AM.
“Some people spend an entire lifetime wondering if they made a difference in the world. But, the Marines don't have that problem.” Ronald Reagan
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |