@Waksupi.
That is the exact method I used on that one rifle that I had to form a Depression in the Cheek piece to get it to stop kicking my cheekbone.
@Waksupi.
That is the exact method I used on that one rifle that I had to form a Depression in the Cheek piece to get it to stop kicking my cheekbone.
Part of my issue was .......the thing kicked
54 cal with a 15/16 barrel, light wood stock, it weighed less than 7 pounds. I started shooting it with 120 grains FFg - dang thing shot so good I kept doin it - then backed off to 100 - I ran the numbers through one of those online calculators and got its well in excess of a 30-06.
Hits right where ya point it so long as ya dont blink - after the stock rework its much better - got a bit of a soft spot for this cannon, over the years its got me a couple of good wins against some pretty stiff competition.
I had a guy bring me a TC Renagade that he said Kicked him if he did hunting loads.
He also said it was Barrel Heavy for him.
I cast up a 3/4" lead rod that weighed about 1 lb.
I took off the butt plate and drilled a hole in the stock for the lead weight.
I glued it into the stock with caulking.
He said that solved both of his problems.
I had installed a recoil pad on that stock before.
But he said that didn't help enough.
Good job!!
I made a 2 pound lead buttplate for my carbine weight sharps - cured the recoil problem - it drags its tail now but get used to it
I did your trick and added a pound rod to my 76 Uberti, already had the hole bored in the stock for the (non existent) cleaning rod that stores there. I reckoned the gun didnt shoot as accurate with it in so removed after a couple of shoots - proly all in me head ??????
The weight and balance of a rifle all depends on the shooter.
Like I had someone ask me to cut 8" off a Long Barrel Kit Carson rifle to make it fit him better.
It worked great for him as you probably seen in other posts.
Now he is thinking about going to a different Rear Sight to fit his eyes better.
You might be correct Joe.
But that rifle was for a Skinny First Time Shooter.
Front weight was not to his liking.
correct for me - took a while to figure it out too ! (skinny I am not!)
with your help he will figure out what works best for him
teach him to shoot offhand - there is huge satisfaction in shooting a nice target standing
I turned 40 (in 1988) some fellers that never rode act the fool and buy a Harley, others trade in their faithful wife for a 25 year old blonde, I decided to revamp my gun cabinet .
Changed out a fair bit of stuff and on a whim I bought a CVA kentucky kit gun - had some blackpowder from foolin around with old winchesters twenty years previous.
But knew absolutely nothing - I got Sam Fadalas "Complete Blackpowder Handbook" and the Blackpowder Loading Manual. Wished I had done that 25 years earlier -
my family were shotgun people (we had a few 22's) nobody taught me anything about iron sights - I couldnt hit with them - bought a crummy little scope when I was 15 and cobbled up a mounting system for my 22single shot - yep that worked - from then until I 'met' Sam I shot scopes and leaned on things to get steady enough to hit.
So that little Kentucky kit and Sam Fadalas instruction book opened a door to a whole new world for me
This is just my opinion, but reshaping the stock seem a really extreme way to fix the problem. It seems way easier to simply install taller sights.
Yessir, it sure would be. I've got a tang sight that fits my Lyman Great Plains but have no idea how it would match up with a Thompson Center. Or if it would be taller, I'm gonna have to dig it out and take a look. I sure don't want to have to scrunch over the stock like I do now. Ouch.
The tang on a TC and Lyman are not the same angle.
So the Lyman tang sight had a wedge shaped piece that sits on the tang to make up for the more drop in the tang of the Lyman like the GPR
I have one of those Lyman tang sights that I bought for the Lyman GPR kit I am going to build.
But have used that sight on several of my TC's
Last edited by LAGS; 11-22-2022 at 11:35 AM.
I have reshaped a few and turned super uncomfortable muzzlestuffers into pleasant shooters.
My style is first to install a kinda vintage lookin leather lace up pad. This is twosome important. First off it adds an inch to the LOP. Also if you need more than an inch you can add a bit more to the LOP without it showing (I also need esthetic appeal) . The obvious advantage is ... its a recoil pad.
Next I do the same trick with eyes closed, mount the rifle and open my eyes. This gives an exact indication as to where to begin shaving wood. Personally I do not get along with cheek pieces so my rifles always get this cheek slapping hunk of wood removed.
My TC Hawkins rifle is set with a leather butt pad and the cheekpiece removed as well as the comb carved down from the buttplate to the beginning of the comb rite at the end of the wrist. I also installed a 54 cal 32 inch 66 twist roundball barrel on it. Green mountain barrel.
Remember...your head height is dependant on either the comb height or the front sight height. For me the cheekpiece always seems to be a slapper ... unless of course it has castoff built into the stock.
Thats my bit.
You say you can shoot the ones your sons shoot no problem. Sounds to me like you need to trade guns with one of them. Problem solved.
We're all different, which is why guns should be.
Good candidate for a Renegade.
I too like stocks that have a larger drop in the stock.
My favorite stock is my Mowrey .50 cal.
It is a basic copy of an 1835 Ethan Allen rifle.
My favorite rifle style is the Hawkens.
But those too I like better with the drop in the stock like the Lyman GPR's.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |