Hi all, this may be wrong part of forum, but I was thinking of loading some 00 buckshot in either .38 special or .357 mag cases. I know 000 is correct size,but I don't have any and have a 00 mold. Any tips and such would be appreciated. Mac
Hi all, this may be wrong part of forum, but I was thinking of loading some 00 buckshot in either .38 special or .357 mag cases. I know 000 is correct size,but I don't have any and have a 00 mold. Any tips and such would be appreciated. Mac
As you mention you need a 000 mold. Lee makes them and I saw them on eBay. DO NOT load a ball hard down on smokeless powders. Find a way to crimp into the ball. Even a light load of two or three grains of Bullseye will generate too much pressure otherwise. I speak from experience.
"You will wantonly strike a hornet's nest which extends from mountains to ocean, and legions, now quiet, will swarm out and sting us to death. It is unnecessary; it puts us in the wrong; it is fatal." Robert Toombs, Democrat of Georgia, warning of the results of the imminent attack of the Confederacy upon Fort Sumter in Charleston Harbor, 1861
Do you have any other 38 moulds and a gas check?
You can use the gas check inside the driving band section of the mould to partition off a small part of the mould and cast smaller wadcutters. Then you can stack a few of these or load a single one.
They have more bearing surface to them so you get better powder burn with a single vs. a single round ball
I’ve done this with a 45-70 mould to make some nice light plinkers. The pic below is with hot glue to show how it’s done.
They are just about the same size as the cuts for the driving bands. So they can’t move around at all.
Pop the bullets out. The check usually falls off depending if you put the cup right side up or upside down. Then re use the check again. They don’t stay on the bullet.
If someone were crafty they could make up a nice little copper disc that would fit perfectly into the groove
I tried 3 pellets of #1 buckshot in a speer shot capsule. it shot pretty good. At 10 yards pellets were about 7-8 inches apart
Life Member of NRA,NTA,DAV ,ITA. Also member of FTA,CBA
Its not .38 but I load .32 auto with 1 .310 buckshot over 1.5 gr Bullseye and 2 meat tray foam discs.
Very soft shooting and surprisingly accurate at 10 yards out of a Seecamp automatic. I'm sure similar load would work in .38 spc.
I don’t know if you ever picked up a 000 mold or had a chance to follow through on this.
I run my 000 through a 358 size. It puts just enough of an equatorial ring around to crimp into and, presumably, grip some rifling. Loaded as pictured, they cycle through my Marlin 1894 just like any other cartridge. I use 357 brass and (I think, but I’m not 100% sure) 2.5 grains of Trailboss.
They are squirrel-head accurate out to around 25 yards, at which point accuracy turns to garbage pretty quickly. But, they work fine for plinking, only consume 70 grains of lead per shot, and at 18 rounds per cast, it doesn’t take much time at all to get many hundred rounds ready.
Sent from my iPhone using Tapatalk
Look on castpics/articles at .38 Special 2 ball loads.
I bumped some in my sizer to .358". The lower had two flats and the upper had a flat on bottom and round on top. Loaded both 2 and 3 ball loads in the .38 Special and .357 respectively. For grouping, the .38 Special 2 ball load performed very well. Better than the 3 ball .357.
I used a .357 round ball and bumped it in my 450 sizer.
Make a fine in-house home defense load. Killed a couple of snakes outside with it./beagle
diplomacy is being able to say, "nice doggie" until you find a big rock.....
after sizing OOO buck, would coating help for heavier loads?
I was thinking the old Lyman mold was 77 gr. Before I bought the mold shown above I was thumb pressing in 0.361" RB's. I got the round ball idea from Turner Kirkland in the Dixie Gun Works Catalog. I used smokeless rather than black powder. When I was about 11 or 12 I read the Dixie book cover to cover.
I had a tumbling issue if I did not size the round balls to 358 .
Distinguished, Master,2600 club, President 100 badge holder.
I've used the Lee TL-356-95-RF (380 acp) cast bullet that has been powder coated and NOT sized in very light 38 special loads. Very mild and fun in a single action revolver
Interesting thread, never thought of doing this but gives me more food for thought. Thanks for all the replies and info. You guys are great.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |