THROW IT AWAY, not worth getting hurt over.
THROW IT AWAY, not worth getting hurt over.
I agree. There is no practical way to reliably separate the two without there being some form of cross contamination.
There are those to have, and those who will. Shoot, the day I FINALLY got some longshot, I accidentally left the fill cap lose on the powder bottle on my MEC and dumped half a pound on a dirty bench. Just had to raise a salute to the fallen and move on.
MC-130J Driver
Former T-6A Texan II Driver
FAIP Mafia
Hook 'em all
Seems like a lot of angst over a pound of powder. Even accounting for the legendary frugality of the Castboolits Forum.
”We know they are lying, they know they are lying, they know we know they are lying, we know they know we know they are lying, yet they are still lying.” –Aleksandr Isayevich Solzhenitsyn
My Straight Shooters thread:
http://castboolits.gunloads.com/show...raight-shooter
The Pewter Pictures and Hallmarks thread:
http://castboolits.gunloads.com/show...-and-hallmarks
Not to be crass, but hoping to screen separate these two radically different speed/type of powders is plain stupid. We aren’t in the dang zombie apocalypse. Anyone telling you otherwise probably recaps their own tires with Elmers glue and rubber bands, and buys used prophylactics to save money.
jimkim, I just ran a test with my screens and the 2400 will pass through a 20 mesh screen but not a 21 mesh, Hope this helps!
Give me something to believe in. Poison
Arosmith What it takes
A 12 step program
With all respect, at least you caught the mistake before you loaded up some magnum loads with it. At this point,you have a $30-$40 lesson about being more careful next time. Attempting to salvage this powder COULD cost alot more with dire consequences. I'll confess to dumping 4895 in a powder measure half full of 4831. It got discarded.
“You should tell someone what you know. There should be a history, so that men can learn from it.
He smiled. “Men do not learn from history. Each generation believes itself brighter than the last, each believes it can survive the mistakes of the older ones. Each discovers each old thing and they throw up their hands and say ‘See! Look what I have found! Look upon what I know!’ And each believes it is something new.
Louis L’Amour
The Californios
The gun you blow up will cost more than $30.
*
The hospital bill will be more than $30.
*
Dump it. The milk has already been spilled.
If you must do this use two screens one for the red dot and one for the "fines"
Then you can be sure you don't have any red dot fines mixed in with your 2400, or very few at least.
If the 2400 won't pass thru the mesh you should be good.
For a lousy pound of powder, it seems a bit ridiculous.
By the time you locate and buy the screens you could buy another pound of powder.
Have some fun, pour it in an ant hill, use a cannon fuse or a thin trail of powder.
I ran another test though a 20 mesh screen, The red dot will drop 10% fines, The rest will stay, Their is no way to separate the fines. I guess a ton of work might work...30 @ 40 Mesh might work? Burn It.
Give me something to believe in. Poison
Arosmith What it takes
A 12 step program
Tweezers and a magnifier! No mistakes!
Mal
Mal Paso means Bad Pass, just so you know.
I'd mix it well and find something to load with it. Wouldn't bother me one bit. Start low and work up...
I’ve used a dollar store frying pan splatter cover to separate long grains of 4227 (3 to 10 mm) from properly cut 1 and 1.5 mm kernels. Worked well (I double sifted) but it was all 4227. You can see a real long kernel below the ruler logo.
No real need to separate the long stuff other than wanting to drop consistent weight charges. Don’t know I’d want to try separating two different powders.
NEVER sift powder to separate by type!!! Not worth the RISK at all. Be thankful more wasn't lost. Injury is far more costly than a little powder even these days.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |