Rule of Thumb … width of case mouth so 1/2 of the bullet base can be seated in the case
Last edited by John Boy; 05-03-2022 at 05:40 PM.
Regards
John
Cast bullets do not need much if any "neck tension". Loading 'em like J-words just distorts 'em. If you need retention against revolver recoil, that's what a firm roll crimp is for. That's tough enough on your brass without flaring it every time.
Cognitive Dissident
In 44 special have found I can use .002 neck tension with both 50/50 ww/PB and straight WW alloy, but if I try .003, I get base swaging. So for atleast with those alloys, .002 is the max. I haven’t tried harder alloys.
Ok, that makes a lot more sense. There are a number of problems with the NOE plugs, and yes, I do have a lot of experience with them. I modify them on a lathe to make them more useable, but they aren't perfect. I personally feel the step NOE just isn't good. It could be acceptable if it were bigger. In your case, you are getting adequate expansion. In most instances, having that step only .004" over the body diameter is far from enough. Anyone who claims to use one that is .001" or .002" under bullet dimeter (meaning the step is .003" or .002" over bullet diameter), and not shaving lead, is not paying attention. They are definitely shaving lead unless they are chamfering the case mouth. I don't want to chamfer my case mouths when a flare works without it. .010" over would be more realistic. I personally don't see any reason to use anything except a flare. The pictured below "modified" is how the NOE plugs should come if they really wanted to make a superior product. There's no reason to have so much surface on them, and there's no reason not to flare. The surface issue especially sucks. I've been reloading for quite a while, and never stuck a case in a FL sizing die. In the few years I've used the NOE plugs, I've ripped the rim off a number of cases. There's no reason not to have them drilled for powder through either. I'm sure they work for you, which is great, but for a lot of us, they aren't perfect. I use them when I have to, but they are just another tool. If they were modified, they could become the perfect solution.
I use NOE expanders… Tonight I was seating some light load 38 Special using mixed brass and old Herters WCs that are like half jacketed (a first for me). Oddly the bullets set into the expanded step for the bullet, then after seating the bullet (no lead shaving) I decided to check them in the cylinder of my GP100. To my surprise, all dropped in except for two that went most of the way in. I gave them both a little pressure and think they may have went in but decided to check them tomorrow to see if they just need a little more crimp.
At any rate, the old flare will get the job done but the NOE sure does a fine job at providing Buck tension and expanding for the bullet.
My main actually only issue with NOE is that on one instance, the .316” plug was catching the mouth lip on the 7.62x54R brass folding it over. I had to go slow on those to ensure the brass was centered in the plug. While that is a pretty over sized bullet I’m seating, I think a little more taper on the bottom of the plug would be beneficial
I’ve used the NOE 454x450 with .452 bullets in 45 auto, and I’ve not experienced lead shavings. I load carefully though to avoid it. No chamfer of the case mouth.
I have used the same .002 difference in 44 special with no shaving, but with chamfering. However the length isn’t sufficient for my bullets, barely expanding the length of the driving bands with none to spare.
If my seater die were shaving lead when the case mouth has those dimensions, I'd ask myself whether my seater stem was not concentric or didn't fit the bullet nose correctly.
And how in blazes can the expander have anything to do with sticking cases in the sizer die? It gets used after the case has gone through the sizing operation.
Cognitive Dissident
sight/touch/feel. I don't trim cases so they are all different. Using the Lee flare tool in the SS press, I set it to touch the mouth, then give it a hard tap (estimate how far the handle needs to move). And keep it handy in the Lee hand press when seating so if there is one a bit small, pop it again. If it doesn't set 1/2 GC depth, enlarge (estimate for PB). For thin necks like 30/30 I use a single twist of needle nose pliers. If not right, another twist does the job. I don't have a progressive press so no problem.
Whatever!
Take this to the bank, you’ll learn quick enough when you over bell a case when you put them in the FL sizing die and the die won’t close … one recycle scrap case
Regards
John
just enough to accept the gas check
Death to every foe and traitor and hurrah, my boys, for freedom !
Consider the case of the .38 Special. The case mouth gets flared, then crimped, then flared, then crimped, over and over again. Now think about a narrow band of metal, say, .010 wide, right at the mouth. It gets work-hardened twice in each cycle, leading to cracking. If you don't flare, that band gets worked less. The conclusion is obvious.
Cognitive Dissident
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |