I have a Howa Mini-Mauser in .223 and it might cover both of your first needs. It weighs less than 6 lbs so it fits the "walking varmint" slot and it will shoot accurately to 300 yards. I am planning to get a Boyd's stock for it.
I understand the other "blanks" you want to fill, but question the need vs cost. I knew a guy who would travel out west from MI with his buddy to shoot prairie dogs at very long range. He used a 6.5/284 and that must have cost him a small fortune to build and load for...and for what? Not like it is something you can eat or mount on a wall. He did it three times and once the new had worn off realized it was not worth doing anymore. He told me most of the varmints fell to his .223 at less than 300 yards. Is stretching a .223 to 400 yards less fun than using a dedicated long range rifle at 600 yards? And if you miss a varmint at 400 yards, does it matter? Just something to ponder.
It comes down to the 80-20 rule. 80% of the time your .223 is going to be perfect. To have the "right" rifle for the other 20% of your shots will cost 2-3 times as much to build and shoot. And now you need to lug two rifles out on "safari".
I went down a similar rabbit hole. Had at various times a .243. 6mm, .243 WSSM and .25/06. Sold them all and 'make do' with the .223. But I do not "need" to shoot varmints beyond 300 yards in order to eat, or sell a pelt.
Don Verna
I think I would start with a used Remington 700 in .223 with the idea of rebarreling it in .223 with a faster twist quality custom barrel. Usually your shots will be under 300yds. anyway and you have already amassed brass for it...
If you really want a 20 something on a 223 case, and we're being frugal on the budget...
Custom dies are expensive. Custom reamers are expensive also.
How about a 204x223, or a 204 short?
Essentially just a sort chambered 204, run the reamer in to 223 length and trim the base off of stock 204 dies...
If you want to spend money, spend it on a Custom barrel, Kreiger maybe?
Last edited by lar45; 11-28-2021 at 11:59 AM. Reason: Auto correct
I have the Stevens (the cheap vs. of Savage) it came with a 111 action and a great trigger. It shoot minute of angle with Hornady Tap 223 ammo and I would not part with it....this was my first Savage and it wont be my last!
When guns are outlawed only criminals and the government will have them and at that time I will see very little difference in either!
"Within the covers of the Bible are the answers for all the problems man faces." President Ronald Reagan
"We must reject the idea that every time a law's broken, society is guilty rather than the law breaker. It is time to restore the American precept that each individual is acoutable for his actions." Presdent Ronald Reagan
While I am no particular fan of the Axis, I am of the regular Savage and Stevens rifle’s. Barrel wise there is no difference. I was like you, hung up on cheap .223 brass but in the meantime a good friend unloaded his big stash of once fired Hornady brass in .204.
I was off to the races, bought a varmint weight Savage take off barrel in the 204. What a shooter! Disliked the heaviness and found a sporter barrel. Great shooter as well.
It’s too bad that components are so scarce now as I would say just go 204 and be done with it.
So is the 20 Practical good? You bet. Will it pay to swap it into your Axis?
I do not know. I do know you have a ways to go with stock and trigger changes before I would make the switch. Also the availability of dies and their cost are a factor.
I run from rimfire to the 25-06 and I still do most even on coyotes with 223 but it’s because it’s my “beater rifle” on a ranch (my occupation).
Sorry if I have set you back on your decision making.
Three44s
Quote Originally Posted by Bret4207
“There is more to this than dumping lead in a hole.”
If your choice is a new(used) rifle,consider bolt/case head size.
I have some very accurate cast rigs in 22 chamberings..... the "problem" with the 223 is the limit on what all you can do with that bolt head size? Going with the 22-250,I get the 473 bolt head which has a HUGE family of cartridges that you can barrel for.
A R700 replacement bolt is 150$+... even swapping out a Savage,small head to large has gotten a little/lot pricey'er. Nothing wrong with a 223,just have to know it's limitations.
I bought a Savage 111 long action in .223 (yes the blind mag had a spacer from factory)
Mostly because I got it Cheap as the barrel was shot out.
I decided to be different and went with .224 Valkyrie.
Got a barrel from Crown Ridge Barrel works https://www.crownridgebarrelworks.com/
and go/ no go gauges and did the swap myself. ( new bolt head from PTG )
possibly one of my most accurate rifles (after break in )
Really likes the Hornady 88 Gr ELD bullets.
Do, or do not.
There is no try.
Yoda
Blanco, what twist rate is the barrel?
If your mind goes blank don't forget to turn off the sound!
1~7 twist
Do, or do not.
There is no try.
Yoda
223AI and AA2520 powder with 53gr vmax. IIRC, velocities are right near 3600fps, 1-12" twist.
In 2005, I bought a 204, in a savage bolt gun, the caliber was new , and the brass was expensive, took the gun to savage shooter down in Ohio, and he rechambered it to 20 tactical, it wil equal 22-250 out to 500 yds, 223 is a great round, but the 20's are better, 20 vartarg, is the most effecient round we tried, same range as a 223, I have both!
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |