Powder coated bullets pics only

[Bowhunter73]

First try with Smokes JD Green NOE 459-300 HP20210629_173510.jpg20210629_173529_004.jpg

[Chamokaneman]

Please don't take what I'm about to say as putting your work down, because that is not my intention.
The matte black from HF really needs to be applied with an electrostatic gun (ESG) for good results. Here's what that HF Matte Black can look like if applied with the HF ESG.

Attachment 281953

The HF red does better, but still isn't a really good powder.

Sounds about right. It took 2 tumbles to coat and the first one looked like about 5% coverage. They work pretty good as 9mm blasters but I think I'm going to get another powder from smokes or Eastwood to shake and bake with going forward.

Sent from my TA-1025 using Tapatalk

[Helka]

Just finished up making a “Zombie” PC coat.




Sent from my iPhone using Tapatalk

[DxieLandMan]

No new posts in a few weeks? Let's see some more pictures. I will post a few when I get everything set back up

[Helka]

Just finished some powder coating.




Sent from my iPhone using Tapatalk

[truck driver]

A little late to the party but this is my first attempt at powder coating.
These are with Smokes blue powder

[almar]

Some samples, 450 grain 50 cal eastwood ford blue and the other, 200 gr 45 cal mix of white and blue.

20211017_092008.jpg

[Helka]

Just did a batch of 45 cal for a friend. I don’t own a 45 yet….





Sent from my iPhone using Tapatalk

[Charlie Horse]

Here is my work with traffic purple in the 38. powder1.jpg

[Cast10]

First time doing 9mm ; Smoke’s Yellow Green ; Lee 356-120-TC

[oley55]

4:1 gloss clear n black Smokes powder. Shake n bake, stood up in silicone mini ice cubes tray.

[truck driver]

Here's some JD Green .45 acp loadedKIMG0799.jpgKIMG0798.jpg

[reedap1]

44 Magnum, 240-grain cast shake and bake coated with Smoke's Flame Red

KUPNwpU.jpg

[truck driver]

I have a few thousand .358 hollow base wad cutters on hand and shoot them in my custom 1911 .38spl. The problem is they lead the throat of the barrel so I decided to clean and PC some to see if it will stop the leading.
Here are before and after coating pictures.KIMG0808(1).jpgKIMG0807(1).jpg

[StuBach]

I have a few thousand .358 hollow base wad cutters on hand and shoot them in my custom 1911 .38spl. The problem is they lead the throat of the barrel so I decided to clean and PC some to see if it will stop the leading.
Here are before and after coating pictures.KIMG0808(1).jpgKIMG0807(1).jpg

Looks like the good old H&G #50. That has long been a family favorite and I can attest to PC makes those work perfectly but I only shoot it in revolvers. Are those the Miha clone with the hollow base option or an original? Curious if the hollow base option might give you better results.

[truck driver]

Looks like the good old H&G #50. That has long been a family favorite and I can attest to PC makes those work perfectly but I only shoot it in revolvers. Are those the Miha clone with the hollow base option or an original? Curious if the hollow base option might give you better results.

These are commercial swaged HBWCs made by Hornady.
I coated them with Smokes traffic Blue PC

[Bayou52]

Range ready! Eastwood Ford Light Blue:

[Taterhead]

Looks like the good old H&G #50. That has long been a family favorite and I can attest to PC makes those work perfectly but I only shoot it in revolvers. Are those the Miha clone with the hollow base option or an original? Curious if the hollow base option might give you better results.

Those are not the H&G 50. Here is the #50 from a mold that I used to own. Pic 1 is to show the location of the heel relative to the cannelure midway down the typical wadcutter brass (it's the only decent pic I have of the as-cast bullet).

[truck driver]

Here's one I recovered from a dirt back stop, .38 148gr swaged HBWCKIMG0816_03.jpg

[WinchesterM1]

Here is a new one for me Kawasaki green with crimson red, it looks camo, this is shake and bake on a NOE 310 nlg 170 FNAttachment 291017