What kind of lubricant do you use for lubing bread?
What kind of lubricant do you use for lubing bread?
"When the homeland is in danger, everything is allowed, except not to defend it."
Gral. Don José de San Martin.
Butter???
Hold Still Varmint; while I plugs Yer!
Blueberry jam?
Sorry if I come off the wrong way... post your question in your first language, and I’ll see what google translate does.
If I understand your question, do you mean what type of lube do we use for cast bullets that requires some heat to flow in a lubrisizer?
I like a soft 50 50 beeswax but I have one of my 450's set up with a solder iron with adjustable heat. It doesn't take much. I have a Christmas tree light on one I never turn off. I have 4 lube sizers and 3 have different lubes. If too hot lube will squirt out. Liquid Alox will work also and you don't need equipment if the boolit is the correct size. I do that also. I load 98% pistol loads for mid range.
I started using Felix lube exclusively a few years ago. It does require a small amount of heat to flow reliably in my lubrisizer. I have an older Lyman 450, which does not have a provision for a heater. I use an automotive engine block heater as a heat source. It is magnetic and I place it on a steel plate that I fabricated that mounts under the base of the 450.
You're good ... Speaking Cajun French comes in handy sometimes ... the bread and butter thing had me sideways !
I don't use hard lubes , over the years I have found soft lubes to do a better job especially in handgun loads .
I've picked up way too many recovered boolits with hard blue / red lube still stuck in the lube grooves ... it needs to be in the gun barrel to do any good .
Gary
Last edited by gwpercle; 05-05-2021 at 02:52 PM.
Certified Cajun
Proud Member of The Basket of Deplorables
" Let's Go Brandon !"
The function of lubricants is to seal and lubricate, therefore, a lubricant whose dripping temperature is high is convenient, or it is not.?
"When the homeland is in danger, everything is allowed, except not to defend it."
Gral. Don José de San Martin.
You have to compare the temperature range of your lube to the temperature range of your environment & barrel. Not all lubes span the same range, so a narrow range & high melting temperature lube may not actually behave as a lube. If the lube stays on one side of the boolit while flying from barrel to target, accuracy will suffer.
*
I want the lube to not melt and flow into the gun powder, while storing rounds in my black car in the South Carolina sun. No higher. After that, the lube must be liquid enough to leave the boolit at the muzzle on cold days. Even with that, I have to acknowledge that I am pursuing curiosity more than necessity.
*
Be careful asking questions about lube. Before you know it, you’ll be dissolving solid lithium, and making your own lithium greases. I’m not the first people doing this
*
Have you considered Felix lube?
Felix lube is the only one I use. It does not require heat at room temp. In a cool loading area (60 deg F) I preheat the sizer with a hair dryer and usually don't have to reheat before I have finished a batch.
I use WLL Alox 50/50 or XLOX 2500 and unless I let my reloading room temp drop into the lower 60's have not found a heater necessary. The few times i needed to warm the sizer I put the little electric space heater I use in my shop on the bench with the fan blowing on the 450 and in maybe ten minutes it warms and the lube flows like it should.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |