Lubed, sized, and checked some 6.5
Lubed, sized, and checked some 6.5
Working at sorting prepping 2,000 once fired 9mm cases. Have a pile of 1-2 K 5.56 cases that are next. Apperantly theres a shortage of 9mm and .223. Guess who everyone is calling.
Loading some 32 H&R mags. I'm going to use my Lee hand press just cause. I'm only doing 50 anyway. I'll use the ram prime too. I'm going to see if I can find a Lee dipper to use too. Just have to pick a load here in a few minutes. I've sized and deprimed and they are in the tumbler right now.
I'll be using powder coated Lee TL314-90-SWC and HP-231 looks like 3.0gr but I'll see if I can find a dipper that will be close to that.
Sent from my SM-N950U using Tapatalk
I'm in the process of sorting through my stash of 223 brass trying to find 1000 that are crimped, dinged, dented or just plain ugly. Planning on shooting them in an AR in a place where recovering the brass will be difficult. Just took the first 500 out of the tumbler to dry.
I cast some of those MP 44 cal devastators - man it is hard to get proper nose fill out with the penta points... They look super cool when you get one, but I've got a 2 cavity mold and I get a perfect one about every 3rd cast. I tried a lot of things - hotter lead, more tin, got the mold hotter, pressure cast, etc... It's just a tricky mold.
After a while, I thought - I've got 30 lbs of 44 cal boolits... I kinda need 40 cal boolits... So I switched and cast about 15# of my 180 grain 40s.
WWG1WGA
Loaded some 45-70 retina detachers and some bp loads also
Those who would trade freedom for safety deserves neither and will lose both
Good evening,
Loaded up 100, 300 Blackout for a bolt Rem 700. I use the NOE 30XCB 2500 lube and aluminum gas check. They are right at 1850FPS with H110. Perfect for 100 meter dingers!! Plan on hunting in a couple months with it.
Also loaded up 90 284’s with J-words for a F-class match coming....
Then swept the floor and straightened up the bench a bit. Promised myself I would spend 15 minutes every time I reload cleaning up. Everything has a tendency to over run the benches....
So far it’s been an excellent weekend
Bullseye67
Broke out the Lyman 266469 yesterday and cast up a couple hundred. Hope to continue with this later today, body and attitude permitting.
These will eventually be put thru a re-barreled(6.5x55) Savage 110 which is the latest project.
https://wbrpc.org/
genealogy, another area of interest
feedback - http://castboolits.gunloads.com/show...9613-czech_too
Sized a small tub of 9mm.
Waiting on an M die to arrive. I pulled down a few loaded rounds and the brass is sizing down the base of the boolits.
Needing to coat more boolits with Hi Tech but it's too hot and humid to try to play with an oven in the garage
Got a used Lyman 45 luber up and running. Needs more TLC but its functional right now
Joe
I'm a Red Cross blood donor- are you? Make an appointment to donate today http://www.redcrossblood.org/make-donation
http://www.redcrossblood.org/
FOR Disaster Relief DONATIONS-
http://http://www.redcross.org/charitable-donations
Mal
Mal Paso means Bad Pass, just so you know.
Wet tumbled 1000 9mms, 1500 .38 specials and 2000 .45 ACP. Finally ready to start reloading.
New 223 dies arrived this week and finally got a chance to use at least the decapping/sizing die. Decapped and sized my first 100 GFL brass tonight and have another 100 PMC to do tomorrow and also hopefully by friend comes thru tomorrow with some primers we are swapping. Getting anxious to shoot these in the new Savage bolt gun.
Started powder coating the backlog of boolits floating around the garage... Looks like I have a week or so of PCing ahead of me.
WWG1WGA
Spent a few hours Saturday depriming, sizing, case cleaning (wet method/oven dry) and repriming 300 cases for 380 ACP....that all just takes time on a single stage press. Hopefully, this week I can get time to charge/cap them.
redhawk
The only stupid question...is the unasked one.
Not all who wander....are lost.
"Common Sense" is like a flower. It doesn't grow in everyone's garden.
What doesn't kill you, makes you stronger...or mutates...then tries to kill you again!
If more government is the answer, then it was a really stupid question. - Ronald Reagan
More 350 & 450 Sub loads!!
NRA Life member • REMEMBER, FREEDOM IS NOT FREE its being paid for in BLOOD.
Come visit my RUMBLE & uTube page's !!
https://www.RUMBLE.com/user/Cwlongshot
https://youtube.com/channel/UCBOIIvlk30qD5a7xVLfmyfw
Lubed some 358429 using the Lyman lubesizer today.
I'm a Red Cross blood donor- are you? Make an appointment to donate today http://www.redcrossblood.org/make-donation
http://www.redcrossblood.org/
FOR Disaster Relief DONATIONS-
http://http://www.redcross.org/charitable-donations
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |