Does anybody know the maximum length cartridge that a rolling block will allow to be chambered.
Does anybody know the maximum length cartridge that a rolling block will allow to be chambered.
It is limited by barrel length, any cartridge longer than the barrel will perform poorly
Really. That's good to hear. I guess I don't need to worry that a Remington roller will easily chamber a 45-120 3-1/4" cartridge. I was a bit conserned that the block might prevent a cartridge of that length from chambering. Hence my question. I know of no problems with shorter length cartridges, but serious concerns on the 45-120 gave me pause.
Political correctness is a national suicide pact.
I am a sovereign individual, accountable
only to God and my own conscience.
Well let me ask this another way that may be clearer. As I'm sure everyone knows there is a distinct advantage to a falling block action when it comes to inserting a long cartridge over inserting the same cartridge into a rolling block action due to the block mechanism getting in the way of inserting a overly long cartridge. So, does anyone have an educated guess what the maximum length cartridge would be before the block interfered with loading the cartridge into the chamber on a Remington / Husqvarna roller.
With a rolling block you do have some limitations, the hammer nose is the interfering point. The length,diameter and taper of the cartridge have a bearing what will fit. A .50 x 3-1/4 probably isn't going to go without modifying the hammer nose. If you look at the hammer of a RB chambered for a shotgun shell you see what needs to be done.
Actually George Nonte did this in the 70's and found out that a 3" 45 case was too long to pas the hammer nose and IIRR he ground the hammer down to get the ctg in.
The maximum length has more than just length to consider. Rim and base diameter come into play also. A smaller rim and base diameter will clear the breech block easier, and allow longer length.
But the block contour also affects what length and base diameter the Rolling Block will accept. So if your donor rifle has one of the concave breech blocks machined to clearance larger rim and base diameters, then it will accept longer, and larger cases.
Which breech block does yours have? The flat block, or the concave?
I want to take one of these RB and I'm looking at maybe a 40-82, or something in that realm. Only using BP and cast.
I've had no problems with my Green Mountain barrel and chambered in 40-82WCF on a #5 smokeless receiver.
WW
I think you will be fine with a 40/82 and the rifle you showed in the photo. The hammer appears lower than what I am used to on sporters. The tapered case will very much work in your favor. I'll try to attach a couple photos of a 40/70 2-1/4 (COAL=2.8) for reference. Your case and bullet will be longer but you will see the idea.
There is a lot of clearance in this case.
40-90-2 5/8 bottle neck will also clear the hammer and block.
WW
A roller will not chamber the 45-120 without modification to the hammer nose AND taking some brass off one side of the rim. At least the Pedersoli I had the chamber cut for the 120 wouldn't. I had the barrel set back and re-chambered to 45-70, then sold it.
"In general, the art of government is to take as much money as possible from one class of citizens and give it to another class of citizens" Voltaire'
The common virtue of capitalism is the sharing of equal opportunity. The common vice of socialism is the equal sharing of misery
NRA Benefactor 2008
As stated by some the RB does have AOL issues with longer cartridges. This is strictly from memory and I am not a RB guy but I believe 45-90 is about the limits without having to modify the hammer nose.
http://castboolits.gunloads.com/show...ls%20in%20them.
2nd Amendment of the U.S. Constitution. - "A well regulated Militia, being necessary to the security of a free State, the right of the people to keep and bear Arms, shall not be infringed."
"Before you argue with someone, ask yourself, is that person even mentally mature enough to grasp the concept of different perspectives? Because if not, there’s absolutely no point."
– Amber Veal
"The Highest form of ignorance is when you reject something you don't know anything about".
- Wayne Dyer
Well you guys have come through for me once again. I have not yet found out which # action within the Remington group that the Swedish government decided to license from Remington to manufacture their military arms. I need to drop dutchman a pm maybe there is a way to find out which model Remington action they used.
I thought I read somewhere that the 44-77 was the longest that would fit. So I figured this would be the right place to ask.
Last edited by MOA; 07-09-2020 at 05:24 PM.
2nd Amendment of the U.S. Constitution. - "A well regulated Militia, being necessary to the security of a free State, the right of the people to keep and bear Arms, shall not be infringed."
"Before you argue with someone, ask yourself, is that person even mentally mature enough to grasp the concept of different perspectives? Because if not, there’s absolutely no point."
– Amber Veal
"The Highest form of ignorance is when you reject something you don't know anything about".
- Wayne Dyer
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |