The subject article was published in the May edition of The Single Shot Exchange (SSE) Magazine. If you are not a subscriber you can access the article at the following link. http://www.texas-mac.com/BPCR_Brass_...a_Tumbler.html
Wayne
The subject article was published in the May edition of The Single Shot Exchange (SSE) Magazine. If you are not a subscriber you can access the article at the following link. http://www.texas-mac.com/BPCR_Brass_...a_Tumbler.html
Wayne
NRA Life (Benefactor & President's Council) Member, TSRA Life Member, NSSF member, Author/Publisher of the Browning BPCR book.
Interesting article, THANKS for posting it. But why ceramic media for BPCR cases and stainless pins for everything else? Do the stainless pins harm the thinner walls of the BPCR cases? I have been cleaning brass with the stainless pins for a long time and I have just got back into BP about a year ago and am cleaning my 45-70 brass with stainless pins and so far not seen a problem.
Thanks
Dave
"How a politician stands on the Second Amendment tells you how he or she views you as an individual... as a trustworthy and productive citizen, or as part of an unruly crowd that needs to be lorded, controlled, supervised, and taken care of."
--Rep. Suzanna Gratia Hupp (TX)
Dave, SS pins work very well for cleaning BPCR cases, but the result is burnishing (peening) & flaring of the case lip faster than with ceramic media. For more details on the subject click on the link to the brass cleaning article I referenced in the 1st paragraph of the cleaning solution article. I anneal my brass after each BPCR match, therefore the brass is susceptible to peening more so than cases that are rarely annealed. If SS pins are not causing a problem for you than stick with them. They do clean faster and tend to do a better job of getting the crud out of the "nooks and crannies".
Wayne
Last edited by texasmac; 05-15-2020 at 10:59 PM.
NRA Life (Benefactor & President's Council) Member, TSRA Life Member, NSSF member, Author/Publisher of the Browning BPCR book.
Thanks for the reply. Since I do not resize my brass, only lightly taper crimp to keep the bullet from falling out, I do not anneal very often so I have not noticed any peening.
Dave
"How a politician stands on the Second Amendment tells you how he or she views you as an individual... as a trustworthy and productive citizen, or as part of an unruly crowd that needs to be lorded, controlled, supervised, and taken care of."
--Rep. Suzanna Gratia Hupp (TX)
I don’t believe it’s the SS pins that peen the case mouths, it’s that the pins offer little to no cushioning for the the cases as they churn in the tumbler. Bulkier ceramic media would provide some cushioning or separation to keep the case heads from clunking against delicate case mouths. It’s the case heads hitting the other case mouths that causes the peening.
I run a finger into the case mouth to feel for any peening. If I detect any roughness a couple of turns with my LEE deburring tool nips off the high spots. I like the Lee tool because it not so aggressive at stock removal which makes it more controllable.
I use Cascade powdered dishwashing machine detergent and a little citric acid or Lemi-Shine.
I use to add TSP but I found it makes the wash water too slick and oily feeling.
I think it reduced the the scouring action of the pins by making the cases act like that been lubed or at least churn in a oil bath, the pins just slide over a lubed surfaces of the cases.
Longer tumbling cleans the cases but longer tumbling time just makes more peening.
Last edited by greenjoytj; 07-01-2020 at 11:06 PM.
I agree with you. I don't believe I ever said that SS pins or ceramic media peen the case mouths or lips. If I did that's certainly not what I meant. As noted in the article on case cleaning and peening, I found that peening takes place with cases tumbled in plain water without any media, but the rate of peening is less than with SS pins or ceramic media. A case full of SS pins weigh significantly more than one filled with ceramic media, and when a case full of SS pins bangs into another case the peening is caused by the collision. Ceramic media does not act as a cushion. The peening is less because a full case of ceramic media weighs significantly less than a full case of SS pins, therefore the collisions have less force.
Thanks for your comments. I need to make this clearer in my article on cleaning and peening.
Wayne
NRA Life (Benefactor & President's Council) Member, TSRA Life Member, NSSF member, Author/Publisher of the Browning BPCR book.
Wayne,
I use Cascade and SST pins and my cases come out very clean and bright. I don't see a problem with peening and I use a Tumblers Tumbler as well as the Frankfort Arsenal tumbler that turned faster than the tumblers tumbler and it does not the the rubber lining making it harder then the tumblers tumbler.
But I just about use the barrel full of water and not just covering the cases and media. Maybe the water suds help dampen the cases banging together, I don't know.
I used to put the brass in a gallon jug at the range and shake it to get some of the fouling washed out and I saw that was peening the case lips so I quit doing that.
I been using Cascade for a very long time and you can see the cases pistol and the .44-90 bn cases look like new.
Attachment 262183Attachment 262181Attachment 262182
I get less or no case mouth "rollover" or peening using ceramic. The SS pins was a problem.
My shooting partner Woody gets less peening (ceramic) using less water in the drum. I get al lot of peenimg using less and the fix for me is filling to within an inch of the top - cleaner too in less time. We both have the old slow turning Thumblers Tumbler.
Isn't funny how two people can get two very different results! And using basically the same stuff. We've had a few late night lawn-chair beers on that subject after matches in Raton.
I gave up on the SS pins. The Ceramic is so much easier and better in so many ways.
Chill Wills
Chill Wills,
I agree with you. My extensive experimenting with case cleaning has proven to me beyond a shadow of doubt that, regardless of the media used, a tumbler completely full of water will result in less peening than one with less water.
BTW, tell Woody HI and that he most likely had too many beers when he came up with that conclusion.
Wayne
NRA Life (Benefactor & President's Council) Member, TSRA Life Member, NSSF member, Author/Publisher of the Browning BPCR book.
I use a mix of SST and Ceramic in my Tumblers Tumbler mainly to get the primer pockets cleaner.
That's funny Kurt. A mix of both. Why not if it works best for you!
My clean brass may not win the shiny award some people's do but they are clean. I stopped using Dave's M's stuff. Not because it did not work GREAT, because it does! I only stopped using it because I am cheap and I don't see Dave anymore. The Oxi-clean or any laundry detergent or dishwasher detergent plus Lemi-shine does fine. Plus, Dave stopped going to the Rifle matches I attend and that is how I would get it, buying in person and supporting his cottage business. Dave is a good guy and I hope he is doing well.
Chill Wills
I run two tumblers and one has the mix of the pins and ceramic. I started this when I came back home after two months on the road out your way and Montana shooting matches. I normally don't clean the cases till I get back home. I take 2000 rounds in several calibers and at one time I didn't close a water tight case and some damp air got in the case with the empty's and they were pretty bad so I mixed the media and it did a nice job so I never separated it for that tumbler
Like you I don't care if the brass is shiny I just want it clean. It don't shoot any better when it's bright.
I see Dave now and then at Alma MI but he does not shoot anymore. He gave some pointers once during a .22 silhouette match that I followed and it helped. Fine fellow for sure.
great article, wayne. plenty of good scoop for all tumbler fans. lee's SSE magazine is one of the best, if not the best out there for all things BPCR. highly recommended to all, go get yerself on the SSE mailing list!
i finally chose to go a different route and have long since left the wet tumbler case cleaning devices for an ultra-sonic (hornady 2L). for me, the u/s is just lots faster (1/2 hour), lots quieter (if noise matters to some folks), does a great job of inside case cleaning (most important), and the brass comes out mirror bright. there are lots of different u/s brass cleaning solutions, and while i can and did make my own for awhile, i just use the hornady brand brass concentrate, 3ozs along with a gallon of distilled water, lasts a long time for more than a few cleanings = cheap enuf. once out of the u/s, the solution wet brass is rinsed with tap water and is either is left to dry as is, or wiped down, or tumbled for 5 to 10 minutes with corn media for a quick dry off. i usually just plop the batch o' brass into a large fluffy towel and wipe 'em down, done.
A little confused.... what ill effect does the peening have if you size and flare after?
I rinse my cases with water, vinegar.... Then they go in the dry tumbler. If they are really bad, I use the wet tumbler with SS pins, Dawn, Lemi.
If you cleaning process does result in some peening, resizing will not remove the peened edge but flaring may minimize the effect it has on your loading process. Resizing squeezes the case smaller but has little effect on removing any peening. Most of the flattened or rolled over edge is on the inside of the case lip. Once the bullet is seated, if the flare is removed with a resizing or crimping die the peened edge is forced into the bullet. For those of us that finger seat bullets into fireformed cases without any resizing, a peened edge can be a problem. Slightly flaring the mouth can help finger seating the bullet but when the flare is removed by a die or just pushing the cartridge into the chamber the edge is forced into the bullet. Those reading this that have a problem with peening may be interested in the following article: http://www.texas-mac.com/Removing_Ca..._LIp_Edge.html
Wayne
NRA Life (Benefactor & President's Council) Member, TSRA Life Member, NSSF member, Author/Publisher of the Browning BPCR book.
Wayne - Great article and was surprised to read the multiple combinations you prepared when I opened my current issue of SSE
Strat-O-Sheen and I are old friends, including Dash and ceramic media
My post on Shiloh Rifle forum, May 2014
Strat-O-Sheen: Physical State = Solid
Boric Acid Percentage = 25 to 30%
pH = 7.5 (almost neutral) in 1% solution
The solution I use is 3oz of Strat-O-Sheen in one gallon of distilled water from my dehumififier
I'm working on my 3rd five pound box of the stuff
Then about a year later, got the bright idea to use plain Dash as a foaming/cleaning addition too. With the Dash 3X on the market now, it cleans much better.All it takes is a 2 second squirt of the stuff
My original media and what I still use are Kramer 3mm ceramic triangles - vintage 2013, that have never degraded as a media
In 2015, I put a post on the SASS Wire about using the 3 components with before and after pictures of BPCR cases. The thread ran for 4 or 5 pages, the word got out on the street and it has become a common rotary tumbler cleaning agent with media or pins.
Last edited by John Boy; 05-17-2020 at 01:40 PM.
Regards
John
Excellent info. Thanks for taking time to post!
Edit... For smokeless bulk rifle, I always use stainless steel pins to take the rough edges out after trimming with the Dillon trimmer. I noted early on that I had to use the mouth sizer (Lyman M in most cases), AFTER I ran through the wet tumbler. The process really does do something to the mouth. That’s why I never liked to run wet tumbler for my precision and BP loads (at least not after sizing). Maybe try some ceramic someday but I don’t want to have to figure out a way to clean up the pins. With stainless, I use the magnet. What do folks do for ceramic?
Last edited by djryan13; 05-17-2020 at 05:39 PM.
Pour the brass and media into it with a rinse bucket underneath. Or hand pick the brass out of the drum, rinse the media and decant the water out
Regards
John
My method is the same as John Boy's.
Wayne
NRA Life (Benefactor & President's Council) Member, TSRA Life Member, NSSF member, Author/Publisher of the Browning BPCR book.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |