Those coated election/sale signs hold up really well and leave nice round bullet holes in your target
Those coated election/sale signs hold up really well and leave nice round bullet holes in your target
I made a couple up from 1/4" cold rolled round stock and pipe fittings. 2 uprights in the center. a lower sliding arm think side ways H. it pushed in the ground and the top arm went over the upright rods. The lower arm slide to tension target and hold different sizes. When disassembled it was very compact and light about 5 lbs.
I just got done with mine. Rebar is awesome. 5/8 rebar cutting with a hacksaw. 5' legs with a 3' span. First i held it together in the corner just sandwiched between some plywood clamped together with bolts. Worked so well i had a friend weld it up. I made some leg holders with 3 foot 2x4 with a 3/4 in pipe sticking up 6 inches.
Very slim and portable. Fits between the wheel wells of my Tacoma, along with a take down shooting bench and still room for lots of gear.
Vote Independent, vote Republican, vote Democratic, just don’t vote Incumbent!
I believe in the Bible, Freedom, the Constitution, the Bill of Rights and personal responsibility. My government believes I am narrow minded, intolerant and dangerous.
If you could find one of them folding lawn chairs that the webbing is all tore up on you could strip it down,and have a target stand that is folding,and free standing.I think you could make it look halfway decent if you wanted.
I asked a realtor who was making theirs up and bought a couple. Mine are 1/2" steel frames and legs. Cardboard to cover and duct tape or wire and you're set.
[The Montana Gianni] Front sight and squeeze
Some of our neighbors have " Dump Trump " signs that could just disappear. But seriously , Out at our gun club the prescribed frame is 4' tall and 2'wide frame of 2x2 or 2x3 lumber with card board nailed to it. I just fixed some today because THE RANGE WAS OPEN!!! and I had some card board I had been saving. There is a concern about ricochet so no metal is allowed. They tend to get shot up so I make them out of scrap that doesn't cost anything.
Quis Quis Quis, Quis Liberat Canes
/////////BREAKING NEWS////////////
Millions and millions of American shooters and sportsmen got up, went to work, contributed to society in useful and meaningful ways all over the nation and shot no one today! How do they controll themselves?? Experts Baffled....
I LIKE IKE
Last edited by LUCKYDAWG13; 05-09-2020 at 04:21 PM.
kids that hunt and fish dont mug old ladies
The best target stands I've ever used were made of 2x2's. I bought 4 8 or 10' 2x2's, and cut two @ 6' long, which was long enough to put them over the soybeans I sometimes shot over. I've never met a situation where they didn't work, and work well. I DID take a few extra pains with them, but not much. I cut a notch in one end of the two vertical legs, to fit the square end of the crosspiece. Then I used carpenter's glue and a long screw to attach them together, being careful to make all flats match up. When these dried, the joint was pretty stout. Nails wouldn't have been nearly as effective. A notch was cut at what I thought to be the proper level down lower, and I usually kept it pretty low, so I could put up several targets at once, reducing the number of trips I had to make to change the targets. Use the carpenter's glue and screw again, and it should make for a good, firm frame that should last you a lot longer than you'd think, if you keep it out of the rain.
Then I bored a hole of @ 1/4" dia. about 8-10" from the top, which acted as the swivel pin for the legs. I did this on each side. Make sure you make the legs longer than the bottom of the legs on the front, so you can stand it more square to the direction of the shooter. Then, if you sometimes shoot in windy weather, screw a screw eye into each side of the supporting legs, and take some strong cord, and tie it to the screw eyes. Get some sort of good anchor (tent stakes?) and tie to the other end of the cord, and you can stake these in the ground to prevent the stand from blowing over, or moving in the wind.
I've made several of these over the years, and have yet to find a substantial fault in them. Keep them in the garage or utility bldg. and they'll be with you and serve you well, too, for a long time. It's all in how you treat them that determines how long they'll last.
Where I shoot they have a few of those and guys being their own furring strips and cardboard to use for ‘close quarters combat’ targets since the closest permanent target stands are 25 yards. What I’ve noticed over the years is that you also need to have a couple of cinderblocks to keep them from blowing over if it’s a breezy day.
NRA Endowment Member
Armed people don't march into gas chambers.
The Action guys here use this and variants - I thought they would not hold up in a breeze but they do very well .
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |