Last edited by sfcairborne; 03-30-2020 at 05:58 PM.
Got it to attach, this is the one I’m looking for
That bullet appears to be from the Lee 457-405 mold. It would be a wonderful 45-70 bullet if it cast large enough in the body and the nose fits your bore. I have that mold and it does not fit my 1895 45-70 nor that of a friends rifle. Mine cast a .457 bullet, as it says, which is too small for a Marlin and the nose on mine as I remember is too big to chamber. With Lee you pays your money and takes your chances.
Tom, in his Accurate molds catalog, has in my opinion much better designs in that weight range for your rifle. The Lee bullet is a bore ride design and therefore the nose had to be the perfect diameter. A round-front bullet doesn't have such restrictions. A friend and I both shoot one of Tom's 405 grain 45-70 bullets and it fits and shoots wonderfully, both in Marlin 1895's. I don't have the design number as my friend owns the mold but I can get it for you id you like.
Good Luck,
Rick
Please the info would be great. Been looking at the accurate site so many designs. I’ve got a NOE 405 a Mihec 350 Hp and a 460 grn mold. All size 460. Just looking for another mold.
Silly question: What are the bore and groove depths for your Marlin? Have you slugged the bore and measured? You will need these measurements if you are going to order a proper fitting mold from anyone, not just Tom at Accurate.
Make no mistake -- They will remember how easily you surrendered your rights.
Sounds bad, but I have not. Been sizing to 460 and getting great results/groups with my 405 grain with no leading. Alloy is 50/50
I should mention that Tom can duplicate the bullet you have there. Then you would need your bore dimension because it is a bore-ride design. Specify the body to drop .460 with your alloy and nose diameter to "snugly" fit your bore.
Rick
Ok thank you.
We are using Tom's 46-405DG bullet. We spec'd the bullet at .460 on the driving bands and .458 on the small driving band on the nose. The last batch I cast is with 20-1 alloy and they weigh about 398 grains. Fit and accuracy in our rifles is excellent. He pushes his to about 1,600 fps with 5744 powder but I don't enjoy that much recoil.
I guess I should ask about when your rifle was manufactured? Mine is from 2007 as I recall and his is a little later.
Good Luck,
Rick
My rifle is fairly new I bought it in 2017
That's odd... I have Lee's 457-340 which I believe is essentially the same bullet as the 405 from the crimp groove to the tip of the nose--from the crimp groove to the base, the 405 is a bit longer and it has an extra lube groove. The 457-450 has the MUCH longer nose than the 340 or 405.
I shoot mine in a 1895 Cowboy all the time with zero issues... well, zero issues anymore. Tumble lubing or running them through my lubrisizer gave me terrible leading and accuracy no matter what alloy or lube I used. I started powder coating them and push through sizing at .458" and they're accurate as anything else and the barrel is clean as a whistle.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |