I would use a pair of small, side cutting wire cutters, as used in circuit board manufacture. Take, say, 3 snips, then tumble the shot all together to push down the remaining sprue. Some folks will say to put the box of balls in your car for a week, but I don't drive long distances any more, so I would use a small tumbler with no media.
Thanks thought about that. Going to be looking for a mould with sorue cutter. Using pair of wire nippers now.
I file down a small side cutter to where the cutting edge is flush on the bottom, nip them close then put them in a square 2# peanut jar with a pinch of graphite and tumble them for a few hours
Use a small side cutter then with a small brass hammer, peen the tit flat.
redhawk
The only stupid question...is the unasked one.
Not all who wander....are lost.
"Common Sense" is like a flower. It doesn't grow in everyone's garden.
What doesn't kill you, makes you stronger...or mutates...then tries to kill you again!
If more government is the answer, then it was a really stupid question. - Ronald Reagan
Like that. And the Quote my favorite. I'm doing a 20lb pot of 00 buck.
They make spure cutters for sinker moulds. Check Do-It molds they have them. Doesn't get them all but enough.
Steve,
Life Member NRA
Colorado Rifle Club member
Rocky Mtn Gun Owners member
NAGR member
What you want is called a flush cutter. Or you can grind the back of your side cutters flat.
I'm curious; Has anybody ever tested if removing the sprue mark actually improves the pattern to any degree?
Cap'n Morgan
Cap'n I have made up my mind that it must. Don't be confusing me with facts!
"My main ambition in life is to be on the devil's most wanted list."
Leonard Ravenhill
Go to Wally World and look in the sewing/crafts department. They have side cutters with green rubber handles. Them's the ones. Work great. Trim as close as possible. I throw mine is a RCBS Sidewinder tumbler, add a dash of graphite (no media), turn it on and pull an Elvis (leave the building) as it's loud. Come back and check every couple of hours. When they get smooth enough for your liking, you're there./beagle
diplomacy is being able to say, "nice doggie" until you find a big rock.....
you can get a small tumbler from harbor freight that works pretty good. I glued a couple of small pieces of wood inside the drum; makes the tumble a little more aggressive.
But now the thought will haunt you whenever you're cutting sprues.
I've cast a lot of buckshot, testing molds for a group-buy. When using a hard alloy (and a pair of gloves) the shot would easily snap from the stem, leaving only a small pockmark not likely to affect the ballistic. I planned on trying some buffered loads, using sawdust for buffer, but never got around to it.
Cap'n Morgan
Guillotine type toenail clippers for the pooch works great. Rolling 00 between two steel plates quickly trues up the ball but letting the tumbler do its work without media helps spread the graphite too.
Common sense Gun Safety . . .
Is taught at the Range!
Another great way is not to snip them off but let them cool and take a small pair of pliers and give them a twist, they will look way better than cutting them apart
snip them off flat, then tumble all shot with a dap of powdered graphite, the tumbling will eventually smooth out the flat spots and the graphite coating makes the shot look factory spec.
I use the LEE 18 ball 00 mold and sometimes I snip them off and spray an aerosol graphite from a spray can in the tumbler and let them go for 4 or 5 hours. sometimes I leave them attached and load them and they do OK
Make a ball roller if you need them really round. 6 inch lipped flat plate for the table of a drill press and a 6" plate with a 1/2" drive shank on the back. Run at slow speed and put the balls in the bottom and lower the plate till the balls spin, next thing you know they are plumb round.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |