Hey all, i got this a few months back and have shot round ball out of it but not really had the time to work up shot loads. Is it good to use plastic 20ga wods in a BP gun or will they melt?
thanks
Hey all, i got this a few months back and have shot round ball out of it but not really had the time to work up shot loads. Is it good to use plastic 20ga wods in a BP gun or will they melt?
thanks
Last edited by Handshaker; 01-12-2020 at 12:22 PM.
No. BP won't make the wad seal. You just need a 20ga over powder wad and over shot wad. Or you could go old school and use tow over the powder and over the shot.
QUIS CUSTODIET IPSOS CUSTODES?
Ok got it, i have the shot wods, just didnt know if i might get a better pattern with plastic. WHat about putting a card and then plastic wod over the card?
It's a pain in the butt, but, you're better off to make your own paper shot cups. At least that's been my experience.
"In general, the art of government is to take as much money as possible from one class of citizens and give it to another class of citizens" Voltaire'
The common virtue of capitalism is the sharing of equal opportunity. The common vice of socialism is the equal sharing of misery
NRA Benefactor 2008
Gee my brother's German 20ga dbl worked great with plastic wads. The clay pigeons had a really bad day. We could only get one shot till the smoke cleared, but they fired fine. I did use a over shot card instead of a folded crimp, seeings how the barrels would not fold easy. Guess it depends on the barrel ID.
Gee, your brothers gun must not be a muzzleloader.
"In general, the art of government is to take as much money as possible from one class of citizens and give it to another class of citizens" Voltaire'
The common virtue of capitalism is the sharing of equal opportunity. The common vice of socialism is the equal sharing of misery
NRA Benefactor 2008
B/P and plastic wads will make a good glue in the barrel and broaden your cleaning experience. Use fibre wads from Track of the Wolf.
BPCR use plastic wads . .30” and .60 LDPE see Walters Wads. Many of my BPCR cartridge use plastic wads for better accuracy. They don’t melt and make a mess in your barrel try them you might be surprised.
or use piper hornets/ wasp nest. works great!
A flat disc of from .030 to .060 in thickness is a lot different from a shot cup with over an inch of bearing surface against the bore.
"In general, the art of government is to take as much money as possible from one class of citizens and give it to another class of citizens" Voltaire'
The common virtue of capitalism is the sharing of equal opportunity. The common vice of socialism is the equal sharing of misery
NRA Benefactor 2008
Nuances aside, are you having fun overall with the rig?
I have hovered over the “buy button” more than once. Congrats and hope its an authentic copy to have a great afternoon with!!!
Thanks everyone. Yes this thing is very fun to shoot. I kinda feel like Captain Jack Sparrow in Pirates of the Caribbean.
I've used plastic wads in my 20gauge trade gun with a 42" barrel with no melting. They didn't pattern good even with a card wad under them. You can make shot cups out of post-it notes . sand a 5/8" dowel own enough that when you wrap the note paper it will slide down the barrel, fold it over the end no need to glue it. cut it to hold your shot load before you remove it from the dowel. You may need to cut slits to adjust the pattern Put a hard card wad under the cup load the cup empty with the ramrod then add the shot. It's a good idea to use 2 over shot wads in a double barrel to keep the recoil from loosing the second load
The 3 people a man must be able to trust completely are his gunsmith his doctor & his preacher ..,his gunsmith for his short term health ,his doctor for long term health ,and his preacher incase one of the others mess up.
Good description and explanation of the paper shot cups, Boogie. Much the same as I do.
"In general, the art of government is to take as much money as possible from one class of citizens and give it to another class of citizens" Voltaire'
The common virtue of capitalism is the sharing of equal opportunity. The common vice of socialism is the equal sharing of misery
NRA Benefactor 2008
If I don't slit the cups I get a 2 INCH pattern at 25 yards. If you get holes in your patterns try bedding the shot in the cheapest cornbread mix you can find.
The 3 people a man must be able to trust completely are his gunsmith his doctor & his preacher ..,his gunsmith for his short term health ,his doctor for long term health ,and his preacher incase one of the others mess up.
What does any of this have to do with Paper Patching?
This should be moved to the "Muzzle loading" section.
"I Make the part.............................that makes the parts"
Looking for Bullet Mould Handles, Heavy Duty Replacement Sprue Plates, Adjustable Paper Patch Bullet Moulds? Check here:http://www.kal.castpics.net/
My Feedback!
http://castboolits.gunloads.com/show...Red-River-Rick
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |