here is my parts list Mcmaster-Carr part #'s for my build
qty 1 -6498K637-double acting air cylinder 3/4 bore 5 inch stroke
qty 1 -6498K195-single acting air cylinder 3/4 bore 1/2 stroke for lead pour
qty 1 -6071K12- clevis rod end for 5 inch stroke cyl
qty 1 -6498K42-clevis rod end for 1/2 stroke cyl
qty 2 -5779K157-push connect tube fitting 90 degree 3/8 tube with 1/8 npt thread one for each cyl
qty 1 -5779K115-push connect tube fitting straight 3/8 tube with 1/8 npt thread for 5 inch cyl
25 ft -5112K65- flexible nylon tubing 3/8 of note this is also a for a feed line to the star sizer
qty 2 -62005k333-air flow control valve 3/8 tube note this a flow directional
qty 1 -4501K72-standard wall brass 1/4 pipe size 1 foot long- you cut to length needed for spacers for lead pour pending on what you use as a top plate for lead pour cyl
qty 1 -91251A370- 5/16-24 3 inch long socket head screw box of 5 note only need 2
qty 5 -5779k116- push connect tube fittings straight 3/8 tube with 1/4 npt thread for air control valves
qty 1 -5779k158-push connect tube fitting 90 degree 3/8 tube with 1/4 npt thread for air control valve
qty 1 -8812K52-pressure gauge regulator 1/4 npt in and out
qty 1 -8812K62 -mount for pressure gauge regulator
qty 1 -1023N17-straight flow manifold 4 outlet 1/4 npt 1 inlet 3/8 npt note this also for a air feed line for star sizer
qty 1 -5779K117-push to connect straight adapter 3/8 tube with 3/8 npt thread for in side of manifold block
qty 6 -5779K116-push to connect straight 3/8 with 1/4 npt thread note 4 for manifold ,1 for regulator out and one for star sizer for the regulator inlet your choice I used 9151K47 1/4 npt pipe extension with female quick change coupler
and I used a quick change coupler set for the star sizer lube pressure feed
and option I used 3 of 4450K2 - air muffler on the air control valves to close off the exposed port, keep bugs out
need a 5/16 - 24 tap part#2521A682
and tap drill size letter I drill .272
and don't forget the control panel ,control air valves, and the rear pivot block for the 5 inch cyl
are from HATCH AUTOMATION
thank you Hatch to make this possible
Hatch , I have it dial in now for 9mm 125 rn , made about 4000 so far
I been getting about 600+ after culling out the defects out of 3/4 of a pot
I started using the mr bullet feeder hopper to fill the tubes for the Star, I fill the tube base down and flip the tube around
to nose in for the star
Cool deal.
Remember the automation system isn’t about producing Boolits as fast as you can as it is more for making repeatable quality Boolits every time.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |