I have to crimp over the driving band for a few of my revolvers. Its not a problem, just start low and work up your load to reflect the reduced case capacity.
Many 357 magnum revolvers have cylinders that are too short for the 358429 boolit. Lots of reloaders choose to crimp over the front driving band to get clearance.
As was mentioned before, just start lower and work up. You will be fine.
It would also give you an excuse to buy another revolver.
Both ways work; crimp over the driving band or use 38 Special cases. As you noted, the +p cases are preferred, but Starline makes good cases, always.
Reading the notes on Starline's 38 cases, they claim for their +P cases: "38 SPL+P has no difference from the standard 38 SPL, other than headstamp designation for load segregation. This is due to the fact that our standard case design will handle +P pressures with no problems."
I like to trim 357 cases just sufficiently to allow normal seating and crimping with the long 358429. I get a bit more powder room and those rounds are unlikely to chamber in a standard 38.
The 358429 has varied a little from production run to production run. I had 2 SC and they were minorly different. One of them worked with normal crimp in Ruger NMBH and the other was too long. My Dan Wesson (old) works fine with the Ruger load. I sold off 2 S&W Model 28's simply because of the short cylinders. I sold the long SC mold too.
I'm shooting these 358429s in a Rossi '92 crimped midway on the front band. That can work too.
Oh great, another thread that makes me spend money.
I have shot 358429 lightly taper crimped on the front drive band forever. I've never had a problem with bullet movement in max mag loads. Lyman cast bullet handbook load data for 358429 shows the oal as crimped on the front of the drive band.
"Masculine republics give way to feminine democracies, and feminine democracies give way to tyrannies.” Aristotle
I crimp in the crimp groove for my NMBH and they fit. They are pretty much flush with the front of the cylinder though.
You can miss fast & you can miss a lot, but only hits count.
I accumulated some notes after measuring loaded rounds and cylinder lengths for a good variety of wheelers. Note that all cylinder length measurements include the case rims, typically 0.055". I expect the formatting to vanish when posted.
Overall lengths: 32-20 with 31133 is 1.58 OAL, 327 with 31133 is 1.49, 357 with 173 gr Keith is 1.66, 38 is 1.53, also with 358156 seated out. 44 Special, with 429421HP is 1.57. 357 case trimmed to 1.24” max will chamber in M-27 with Keith bullet. Colt OM cylinder too short for 32-20 or 22 Kay-Chuk, would work with 327.
Cylinder lengths, include 0.055” centerfire rim.
Ruger Super Single Six 32 1.45
Colt Officers 22 LR, WMR 1.55
Colt OM 38 1.56
Colt Army Special 32-20 1.60
Colt Trooper, Python 1.61
K-22 1.62
S&W Outdoorsman, M23,24,27,28 1.62
Colt PPS, Diamondback 1.62-3
FA 97 1.63
Ruger SP101 32 & 38 1.64
DW 32 H&R, 32-20 1.64
S&W M640 1.65
Colt SAA 1.66
Ruger FT, OM 357 1.66
Ruger GP100 357 1.66
S&W M66 1.68
Colt New Service, Shooting Master 1.68
S&W M625 45 Colt 1.72
Ruger Large SA 1.75
S&W MMC 45 Colt (on M57) 1.75
S&W M29, 629 1.75
Bowen Ruger 45 1.85
From inspection, you can see that only the Smith M19 or 66 and the Colt New Service or Shooting Master are comfortably able to swallow a long seated 358429 in a full length 357 case.
I, too crimp to make cartridges work in some revolvers/rifles
haven't had a problem with them collapsing in magazine tubes so figure my crimp is tight enough
NRA Life
USPSA L1314
SASS Life 48747
RVN/Cambodia War Games, 2nd Place
I just checked my dummy in the die box, and for my dad's Security-6 I seat it until the crimp groove just disappears and crimp into the driving band. Your mileage will likely vary.
"It is wrong always, everywhere, and for everyone to believe anything on insufficient evidence."
-W. K. Clifford "The Ethics of Belief"
"They hate you if you're clever, and they despise a fool."
-John Lennon "A Working Class Hero"
i have been using the 358429 in 357 cases crimped on the front driving band for years.it works great. the 358429 was designed for the 38 spl.case for use in the .38-44 s&w.
i use the 358429 for heavy loads in.38 spl. cases. mainly because .38 spl. brass is so cheap. i have 3 buckets full of it now. it works slick through my rossi 92 carbine also.
Works in my two Ruger Blackhawks but too long to feed in the Marlin M1894. I went to the RCBS 38-162-SWC and it works well in all of them./beagle
diplomacy is being able to say, "nice doggie" until you find a big rock.....
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |