[/QUOTE]
Corrected. Thanks for catching that.
As 44mag#1 has pointed out, in full power 500 loads using bullets in the medium weight ranges (440-500 gr.), you need about 4 more grains of 1680 compared to H110 to get similar results.
According to Hodgdon, with the 500 grain Hornady bullet you need 10 to 15 more grains of CFE BLK compared to H110. This would indicate that CFE BLK may be a whole 'nother kettle of fish compared to any powder we've used before in the .500.
Pulling out the calculator while looking at this data, we find other interesting things.
Raising the powder charge of H110 from 31.0 to 33.0 grains (6.5% increase) raises the pressure from 34,400 PSI to 51,900 PSI, a 51% increase.
With CFE BLK, raising the powder charge from 40.8 to 48.0 grains (17.6% increase) raises the pressure from 36,700 PSI to 51,100 PSI, a 39% increase.
As I said, CFE BLK seems to be something we've not seen before.
Last edited by John Ross; 02-06-2018 at 10:07 AM.
JR--the .500 specialist
Just a quick update for some of our members. I have been in touch with Ron Reiber from Hodgdon and as I type this there are brass and bullets headed his way. We use a modified version of Richard Gibson's (Ranger Rick) 700 gr. that he provided us (Ballistic Supply) with in 2004. Steve Brooks made the mold and the only difference is the meplat is slightly smaller in diameter so it is "less a full wadcutter design" and also a plain base.
I test loaded some of them today starting with 30.0 grs. CFE BLK and noted no high pressure signs. I advanced to 32.0 grs. and chronograph readings were a nominal 1,080 fps with a low ES. Primer flattening was becoming apparent and I had hoped to reach 35.0 grs. at which load density would be 100% at the start of compression. Since the components are in route to Hodgdon and they have the RIGHT testing equipment I stopped at this point.
I think the CFE BLK will turn out to be another fine choice of powder for the 500 S&W especially in the 350-500 gr. bullet weights with obvious uses in the heavyweights.
It should also be noted that MP-300 has turned in some impressive numbers, nominal 1,150 fps with the 700 gr. loaded at 26.0 grs. (severe primer flattening at proof loads of 28.0 grs.) and the 26.0 gr. load was very accurate. All info from a S&W with the 8 3/8" barrel
I will post Hodgdon's velocity and pressure readings as soon as I get the numbers back from Ron. The next venture will be to powder coat the 700 gr. and 630 gr HP and see what we can learn from that. Last bit of info for those who use Puff-Lon as a means to reduce leading while reducing hardness for massive expansion .6 cc seems to work fairly well. Hope this helps the "Big Boomer Shooters".
Just received some info back from Callahan Mciver at Hodgdon Powder. The following is from a 10" test barrel using the 700 gr. hardcast loaded to 2.250".
The first test was 25.0 grs. of H-110 which is our standard loading and it gave 1,151 fps at 42,500 psi. and a ES of 11 fps
The second test was with CFE BLK loaded to 34.0 grs. and it gave 1,225 fps at 39,700 psi and a ES of 16 fps.
*** It should be noted that when I used a S&W 500 with the 8 3/8" barrel 32.0 grs. of CFE BLK showed a flattening of the primers this was with a c.o.l of 2.298". So if you are inclined to work your way up to 34.0 grs. of CFE BLK do so in very gradual increments.
Callahan also stated that the 34.0 grs. of CFE BLK was at 100% load density at the 2.250" c.o.l and we have found that 35.0 grs. at 2.298" starts to compress the powder.
All brass used was Starline with Winchester Large Rifle Primers.
Given the other uses for CFE BLK in other calibers I think this is one powder I will always keep on hand. It burns clean and meters BETTER (if that is possible) than H-110 and when using with jacketed slugs it has the benefit of the copper fouling eraser. Hope this info helps, Bill
Michael,
Check your e-mail
Any updates on CFE BLK loads in the .500?
I'm looking to load 400 and 450 grain bullets to 1000-1100 fps
Based on Hodgdon data with 400-500 grain slugs, doing a little interpolating, and realizing that Hodgdon tests in a closed breech 10" barrel, I'd suggest trying 31-33 grains of CFE BLK, if using Cartridge OAL around 2.005" and 5-6 grains more if loading to 2.300" OAL. Pressures should be 20,000 to 30,000 PSI, depending.
Hodgdon lists data for subsonic loads in the .300 Blackout with CFE BLK and pressures as low as 11,400 PSI, so apparently this powder doesn't give squibs like H110 or 296 when loaded down.
JR
JR--the .500 specialist
41grains of CFEBlack, 450Keith gas check, WLR, Starline case ran 1100 out of my four inch. Nice load and looked up the numbers
1112 high 1046 low 1086 ave es 66 sd 24
Last edited by frank505; 03-21-2019 at 10:53 AM.
It's nice to see people "thinking outside the box" a bit concerning fast rifle powders in magnum handgun cartridges. I've done that in the 500 S&W with a 700 gr bullet:
Here are some loads I used in my NEF Handi-Rifle in 500 S&W with the MiHec 700gr:
OAL 2.575"
IMR4198 - 40.0 grs (full) - 1450 fps
BLC-(2) - 48.0 grs (full) - 1200 fps
My experience has been that you can use a full case of IMR or H4198 and any powder slower, with bullets up to 700 grs. I wouldn't go any slower than powders in the BLC-(2) - Varget range. I use a magnum primer only with the ball powders.
CFE BLK being slightly faster than the 4198's, it would be useful in the 500 S&W for all bullet weights - likely close to a full case over a magnum primer (if needed) for the 700 gr (~ 40.0-44.0 grs)
It shows well in the 500 gr and might be a front-runner with the 700 gr - I sold the gun so I can't do the testing myself.
Last edited by Andy_P; 10-02-2021 at 08:47 AM.
I have had unsatisfactory results with the CFE BLK and I suspect it is due to the short 3.3" barrel. Published loads were compressed with cramming 53 gr in there and first off this powder didn't compress at all, was like trying to seat the bullet in cured concrete. The velocities I achieved were consistently well over 150fps slower than the published comparable H110 loads. I even had better velocities using 4759 loads with similar case fill to CFEBLK. As far as accuracy is concerned I unfortunately did not have the environment to add that element to produce any standardized results as this was at a busy public range, just setting up the chrono between firing with a target behind was enough.
Nevertheless, the pound of the stuff I have leftover will probably last a long time.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |