Was at the makeshift range yesterday, picked up some brass and other casings. I need some thoughts on reloading 1. steel casings and 2. aluminum casings.
Dean
Was at the makeshift range yesterday, picked up some brass and other casings. I need some thoughts on reloading 1. steel casings and 2. aluminum casings.
Dean
dont bother. if there was no more brass left on earth, in a pinch the steel can be loaded once or twice. short of that, they go in the trash.
I wouldn't
when the dust settles and the smoke clears all that matters is I hear the words " well done my good and faithfully servant "
<(*)(()><
Take them to the recycling place and trade them for cash....
Tom
μολὼν λαβέ
Did I ever mention that I hate to trim brass?
Life is too short and brass too available to mess with either.
[The Montana Gianni] Front sight and squeeze
Same here, I've done it. If brass cases were not available for some reason, I would load steel and aluminum cases if I had to. It can be done. Since I have gallons of brass in common calibers the steel and aluminum go straight into the garbage or recycling. Brass is so much better and easier that the others just are not worth the time, effort, or risk.
No, nope, un-uh, not in my dies.
More "This is what happened when I,,,,," and less "What would happen if I,,,,"
Last of the original Group Buy Honcho's.
"Dueling should have never been made illegal in this country. It settled lots of issues between folks."- Char-Gar
Rides et Ratio
Steel cases have a shellac varnish type coating that lubricates and helps them to seal and function. This gets thin wears pretty quick. I have never tried it but a polisher might remove it pretty quick. On aluminum cases Ive seen the split the necks on the first firing usually only .020 -.030 long but there. Again a coating is there to lubricate and lower the abrasiveness of aluminum also.
Aluminum: only if NOTHING else was available and then ONLY ONCE. A split case or leaking or blown primer in an aluminum case can mark a chamber or breech face.
Steel: Never, I won't even shoot steel case ammo at all. I have seen steel case .45 ammo break extractors in 1911 pistols.
Brass is available and cheap enough no need to risk damage to a firearm. Exception is firearms "made and designed" to function with steel cased ammo.
Just one persons opinion, Safeshot
Getting old is the best you can hope for.
I don't bother with either. For me it's a one time use thing and their already used. Scrap at best
Don't...
"Freedom is never more than one generation away from extinction. We didn't pass it to our children in the bloodstream. It must be fought for, protected, and handed on for them to do the same......." - Ronald Reagan
"It is foolish and wrong to mourn the men who died. Rather, we should thank God that such men lived." - George Patton
The second amendment is a nail on which hangs a picture of freedom - member Alex 4x4 Tver, Russia
Its been done. Its even been talked about on here. Mostly during the past shortages. But the shortages are over and brass is plentiful. I recommend leaving it alone. Plan to start stocking up now for the next shortage so you don't have to mess with aluminum or steel cases.
Aluminum and steel belong on cars not ammo, my opinion.
I always clean at least the range area I use and separate it at home by color and with a magnet. Only consider using it (other than brass) if no brass is available as in a very rare caliber.
Information not shared. is wasted.
If you like your guns you will not proceed with either ...
[SIZE=4][B]Selling Hi Quality Powdercoating Powder
I carry a Nuke50 because cleaning up the mess is Silly !!
http://www.bing.com/search?q=nuke50&...7ADE&FORM=QBLH
I am not crazy my mom had me tested
Theres a fine line between genius and crazy .. I'm that line
and depending on the day I might just step over that line !!!
I had a T/A Buddy who scavenged everything. He got a load of steel 45 acp cases and polished and reloaded them. He carefully boxed them up, all 500 rounds, and put them in the closet. A couple years later he dug them out to shoot them and most of the cases were rusty and he got a ton of practice at malfunction drills. I still have a couple boxes of these I can send you if you need the practice. Aluminum cases do not resize well and they were losers too, once reloaded they tended to be sticky.
The aluminium cases I have (CCI Blazer 357Mag, 125gr SJHP) are marked "not reloadable," and probably better than 90% of the cases split on firing. Granted the loads seem quite hot, recoil is much harder than any of the 147 and 158 gr ammo I use.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |