What do ya'll think??
Attachment 176020
What do ya'll think??
Attachment 176020
Why is one primer missing? Try to reprime and see if the primer fits snugly.
The remainder look like Glocked brass and a weak firing pin spring.
What did the chronograph say?
Thanks, Yeah, they were all fired from my G34. As for the firing pin, it was the competition firing pin spring. I researched and these are the breech face's mark.
"Competition" parts are a euphemism for "more likely to make the gun malfunction" parts.
I cannot resolve the photo well, but if the firing pin strike is elongated or has a little tail on it instead of a round mark it's a weak firing pin spring that is the culprit.
Now how about answers to my questions?
The missing primer was a result of an explosion due to high pressures. If look closely, the last two cases from left to right are broken. No chrono bud.
Looking at all of the primers as a whole, focusing on the radius of the outside edge of the primers...they say to me that the FPS was all over the place...the loads were probably varying .4 of a grain or so...very wide spread.
Looking at the 3'rd from the right, at this narrow radius...this is the upper limits...for me...for pressure. If I hand trickle each load to build a limited supply of J-type HP's where I am focused on speed, I'll trust this load.
If I intend to load these using 'any powder throw' brand...I deduct .2 grains from the max load just spoken of to compensate for inaccuracy of the throw.
In question for me is this, looking at the ones from the left side..."Why didn't these primers 'reset' to flush?"
It's really too poor of a picture to suggest much more than this.
a m e r i c a n p r a v d a
Be a Patriot . . . expose their lies!
“In a time of deceit, telling the truth is a revolutionary act.” G. Orwell
9mm is very touchy......already a high pressure cartridge, then seat the boolit a little too deeply, and you have a pressure problem. The fact that one completely lost a primer would be enough to say the pressure is too high.
You cannot discover new oceans unless you have the courage to lose sight of the shore
"Explosion due to high pressure"?????
Just what were you doing and why? Is there some reason you wanted to cause problems?
Since you are responsible for this outcome, how did you bring it about?
Check your powder scale make sure its accurate. That why i have two of them to double check my loads. Some times a near max load can be a over load in another gun. No two guns are all way the same when reloading. What is accurate in one gun might not be accurate in the other gun. Max loads are most of the time not the most accurate loads. 30 years of reloading has taught me a few things.
Ouch! Look closely at the two on the right: notice the jagged ruptured brass sticking out above them.
Thanks guys. Yeah the last two were ruptured by pressure. I was doing a ladder system to find the ideal load for a g34 built for competition with a compensator. After receiving some feedback, I realized they were seated too deep. I used the Hornady auto powder system.
Flow of a primer into the firing pin hole is a no-no. Although not flattened, they are signs of pressure.
I look through the one with the primer missing, why such a big flash hole? If that was the result of firing, you have surpassed sanity.
God was smiling on you that day. Someone told me my bhp was the only reason why my hands were still intact, he also told me same load in a glock could have ended up in personal injury. By chance did you use a 1970 vintage Lyman manual? What powder? What charge and bullet weight? What coal were you using. Deff write into your post that this load should be concidered fatal and is only to demonstrate what not to do
Holy sheep! You were ladder loading a 9mm? One case blew out, and you proceed to go the next step up? Reloading might not be the hobby for you.
"I don't want men who miss." -Capt. Leander H. McNelly
Aside from the giant primer hole and blown cases, the primers on the right appear to fill out the primer pockets much more so than the ones on the left.
That's all I can notice given the lighting in the photo.
What bullet were you using and how deep was it seated. How many times has the brass been reloaded?
~~~~~~~~~~~~~~
“If someone has a gun and is trying to kill you, it would be reasonable to shoot back with your own gun.”
― The Dalai Lama, Seattle Times, May 2001
My thoughts as follows:
Use same head stamp for working up loads.
Stop after the 4th round in the ladder.
Pull the remaining rounds apart using a bullet puller.
Happiness is a couple of 38's and a bucket of ammo.
Thanks all. I realized the OAL was too deep, so I seated higher in the case. Also, came to find out that the perfect functioning with the comp, load, and springs was: 5.9grs of WAC with a 13lbs spring.
P.S: The explosion occurred due to a mix of 6.7grs of WAC, seating too deep, and a compressed load.
You want a sign of high pressure? Here's my experience...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |