Hey guys, Ive been meaning to pick up this mold for several years now but never have..Ive saw a few threads were guys bought them but never heard any reports back on how the boolits dropped? Anyone have one? Anything to report? Good castings? Thanks
Hey guys, Ive been meaning to pick up this mold for several years now but never have..Ive saw a few threads were guys bought them but never heard any reports back on how the boolits dropped? Anyone have one? Anything to report? Good castings? Thanks
Well I have only shot the .50 cal maxi ball 370 GN. It is a good accurate bullet and deadly for hunting, I could only imagine it would be great in .32 cal as well.
Front band measures .322 and the rest .317 cast from pure lead. I dont have the mold anymore but i got the 6 cavity from TOW. What gun is it going in? A 1/48 is not near fast enough.
http://castboolits.gunloads.com/show...all&highlight=
Bardo
Cherokee 1-30 twist..Ive shot plenty of maxi balls and still have plenty for my .32 but have been wanting a mold. Tired of borrowing one, know what I mean..
I have one, its fine once you get rolling. I just wish mine was a 1-2 cavity. a 6 Banger for a muzzleloader is overkill. If your picky, and weigh and measure, theres always going to be culls. Half the time, I just cull by eye, unless its for something special. That Cherokee 1-30 I consider the benchmark for the caliber, and I own several including customs. If I had to do things again, they would all have that twist.
Thanks, Id buy a regular ol' T/C one if I could but of course we know how that goes now,LOL..My wifes papaw(93 years old, lives just down the holler) has an original .32 TC mold but he still uses it and still shoots..He's the one I got the Cherokee from..Sweet,sweet little guns aint they?
My 1-48 stabilized the 32 maxi just fine.
I have been shooting a .32 Cherokee for over thirty years and most of that has been with maxi balls cast from an original TC mold purchased from Track of the Wolf back in the eighties. The maxi ball shoots better and loads quicker. One drawback is that you absolutely need to run a wet patch down the bore after each shot. Bullets must be lubed and I keep my powder charges low, using a measure made from a 38 special cawhich works out to about 23 grains of 3F. For 100 yard shooting I increase the load to 30 grains and so don't need to alter my sight setting. The maxi ball outshoots the round ball in the Cherokee due to the quicker twist and it's better at bucking the wind when shooting beyond 25 yards. Shooting the maxi ball enables accurate shooting out to 100 yards. At 50 yards I can keep ten shots in a bullseye that appears smaller than the front bead (an NRA police L handgun target).
The maxi ball and Cherokee combination is my favorite whenever I go to my rifle range. And I love outshooting all the Mall Ninjas with their M4 clones.
Lee makes a 32 wadcutter that works fine and is accurate in my Douglas 32 caplock.
If you want to play in the woods with a bit more throw weight in your rifle. Paper patch or use a thinner patch.
BvT
Every lawbreaker we allow into our nation, or tolerate in our citizen population leads to the further escalation of law breaking of all kinds and acceptance of evil.
Since almost all aspects of our cultural existence are LIBERAL in most states, this means that the nation is on a trajectory to dissolution by the burden of toleration and acceptance of LAWBREAKING as a norm, a trajectory back to the dark ages of history.
BvT
I cast a bunch of .32 maxi's from a TC mold today and the front driving band is about .326 on them..Though TC maxi molds always have a larger driving band than Lyman lyman does too.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |