Been looking at adding one. Any experience? Are they worth it? How picky are they? Any input is appreciated.
Been looking at adding one. Any experience? Are they worth it? How picky are they? Any input is appreciated.
Here is what I've gathered. It's not an easy swap and they are caliber specific. So if you like to load a bunch of different cartridges then you don't want to add one. The people that have them seem to like them a lot.
I'm a little disappointed with the versatility of the 550 case feeder. No 380,32 short,or 25 In pistol. No rifle at all. Works great for the pistol cal. that it does load, no issues.
NRA LIFE MEMBER
ILSA MEMBER
NRA RANGE SAFETY OFFICER
Thanks for the feedback. Sounds like I will pass.
I added one to my 550b and it took awhile to get it set up. Its not something that is easily taken off once its installed but it can be done. The case feeder works fine and will save you a lot of time reloading pistol calibers but won't feed any rifle calibers at all. To fix my problem I've dedicated the 550 to large primer pistol calibers only, 45 acp,44 spl,44 mag and 45 colt and installed a xl650 with a case feeder for small primers only at this time. I do realize that this is an expensive way to reload ammo, however reloading is something I enjoy just about as much as shooting.
NRA Life Member
Nice looking set up Rockchucker!
TEAM HOLLYWOOD
NRA- LIFE TSRA-LIFE SASS-LIFE
Thanks, Its a little crowded but its all the space I have at the moment.
NRA Life Member
I have one, I load 9mm, .38Spl, .357Mag, .44Spl and .44Mag. I have only had one issue and that was the lever that activates the Primer Slider (WAG as to what you call it). When the case feeder went on, it pushed the lever over a little and it was rubbing on the frame of the press, after I removed a little metal from the fram where it was rubbing, the problem went away.
Changing between the listed calibers requires only swapping a coloured tube at the bottom of the case feeding tube, and a small plate that alligns the shell with where it needs to go in station one on the press.
I love it, I can load faster, and it is safer. If you don't manually index the shell plate, the case feeder will feed a second shell into station one, and if you then yank on then handle, it will try and shove two shells into the sizing die, which will give a subtle reminder that you have stuffed up.
WHEN IN DOUBT, USE MORE CLOUT!
I've had one for 8 years and once I got it set up have had no problems at all. It will only work for pistol calibers but it works great. I have heard of all of the problems with the case feeder but haven't had any. To me a must buy if you do a lot of pistol calibers.
I installed one and overall was very disappointed. Basically, it is an add-on for a press that was never designed to have a case feeder, so yes it's finicky. It is also limited as it will not do short cases like the popular 380. I ran two 550 presses since they were first introduced, but about four years ago I decided it was time to move up, so I sold my 550's and purchased two 650's and have never looked back. The 650 was designed to use a case feeder and it's feeder will handle small cases. The 650 is a stronger press and if you load for accuracy, the COAL maintains a tighter tolerance on the 650's than I was ever able to achieve with my 550's. Obviously, the 650 is faster and safer as you can add a a powder check die because you have an additional station. My advice is if you want a case feeder, and who doesn't, is to sell your 550 and purchase the 650, you will be much happier.
http://www.brianenos.com/forums/index.php?showforum=78
check out the dillion specific reloading equipment forum at Brian Enos
check this thread, a hack that shows you can do .300 Blackout thru the casefeeder on the 550b, so you should be able to do .30 carbine too
http://www.brianenos.com/forums/inde...owtopic=157578
there are other people thinking outside the box just like here
and somewhere in that forum I saw where a guy used a vise grips to attach a paint brush before the drop tube to help with better feeding
looking at that picture I did not realize how much larger a 650 is compared to a 550
I ran one on my 550b for 9mm, and decided to sell it a while back. It was cumbersome, and I didn't feel that it added much speed to my reloading on the 550b. I usually don't extensively screen my handgun brass before I start reloading, so occasionally I will have to stop producing to pull the brass off and swage out a primer pocket before continuing. So, for me, the case feeder was more of a hinderance.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |