The presses I use are all handle push down.
I have two old ones that are handle pull up, but never tried them.
Anyone do both????
What is the difference????
The presses I use are all handle push down.
I have two old ones that are handle pull up, but never tried them.
Anyone do both????
What is the difference????
I have used a couple of presses that could operate on the upstroke. Frankly, if you are used to a now normal down stroke operation, and the press is solidly mounted, the down stroke is more ergonomic.
If you want to hold the press in your lap as you load, the up stroke makes sense. The last two that I can think of that operate this way are the Lee hand press and the little Lyman convertible, Acculine?? (I should remember the name, I have one of them). They also work well for completing loads at the range, if you can manage powder handling in the open.
Robert
I have only used down-stroke presses...but I think that I would prefer it, anyway, as it just seems to be more natural from a leverage standpoint.YMMV
In the days before compound leverage, a guy could develop a lot more force lifting up than just pushing down.
My little Pacific can be switched to work up or down.
It's neat, I can push down on the lever to pull bullets or seat primers.
I have a couple of the CH Swage-a-matic presses that operate on the upstroke. You better have your bench really heavy or anchored to the floor for serious upstroke work.
All my other presses are downstroke presses and I much prefer that method. I get more leverage and it just seems more natural. You also aren't trying to lift your bench off the floor.
Hope this helps.
Fred
After a shooting spree, they always want to take the guns away from the people who didn't do it. - William S. Burroughs.
Lots of people can lift more than they weigh. You can also lift more with one hand than you can support of your weight by pushing down with one hand. But--like ReloaderFred said, you better have your bench anchored to the floor.
If I have to work that hard to operate a press, I'm going to get something with better leverage or a motor.
I changed my RCBS JR2 to up stroke because it is worn enough so that the handle falls down and raises the ram by itself. So I would have to reach down to raise the handle and lower the ram first and hold it there before I could do whatever operation I was trying to do. I like raising the handle on the power stroke better for operations that do not require a lot of force, although I have swaged some 41 bullets using 40 cal brass for jackets with this setup. I also have a rock chucker that the power stroke is downward in case I need to really force something.
Quis Quis Quis, Quis Liberat Canes
/////////BREAKING NEWS////////////
Millions and millions of American shooters and sportsmen got up, went to work, contributed to society in useful and meaningful ways all over the nation and shot no one today! How do they controll themselves?? Experts Baffled....
I LIKE IKE
Hmmm, tomato, tomahto. If the operation required my weight pushing down, or enough force lifting to move my bench, I'd find out what's wrong!
My Anchor is holding fast!
I use both types. The only difference is which one works my biceps more than my triceps.
Member: Orange Gunsite Family, NRA-Life, ARTCA, American Legion, & the South Cuyahoga Gun Club.
Caveat Emptor: Do not trust Cavery Grips/American Gripz/Prestige Grips/Stealth Grips from Clayton, NC. He will rip you off.
the original Pacific's were upstroke and stayed that way until 1959. The idea was that using your leg muscles to lift the handle when full length resizing was easier. Your legs are stronger than your arms. It is also where the idea that you need a "strong" bench for reloading comes from.
All that changed thanks to Fred Huntington.
Ken
Is there a kit for converting the old Pacific press to downstroke operation?
Thanks.
David
Cats are fun and magical when you can't smell their poop! Fresh Step!
JPFO; NCOWS; NRA (Life); NYSRPA (Life); SAF, SASS
I'm looking for a shooter grade Smith & Wesson Victory model in .38 Special.
David, since most copies of the Pacific press use the same ram, link and pivot block you may be able to switch parts with another brand press and get down stroke.
Ken
I have several That Use the UP- stroke. Mainly my AA Easton . The Esaton Super Only works with that. . You really do not Need as much force as You Think. . The force Generated In this position is a Lot different. . I found out The hard way Once If your Bench is Not Bolted to your floor . It will start lifting The bench up. after awhile You will not Know the difference. Depending On the caliber , You will get a Better feel when seating Bullets.
Sal
NRA Endowment Member
International Ammunition Association
New York, the Empire State Where Empires were Won and Lost
Cats are fun and magical when you can't smell their poop! Fresh Step!
JPFO; NCOWS; NRA (Life); NYSRPA (Life); SAF, SASS
I'm looking for a shooter grade Smith & Wesson Victory model in .38 Special.
I have two old Lyman Spar-T turret presses that I use exclusively for bullet seating. I shortened the handles and set them up for upstroke use. It is faster, as you only have to pull up. You can simply drop the handle after the bullet is seated. Don't sit closer to the press than the length of the handle.
The ammo doesn't care, so method of press operation is purely a matter of personal choice but modern compound toggle presses are universally down push. I started with a simple toggle linkage press, Lyman Spar-T, in 65; it worked and I still use it sometimes. But I home shop converted it to a compound linage in 2001 and like it a WHOLE LOT better now. Many of the old presses had toggle blocks that can be reversed to change the direction of operation.
Brass is pretty soft and malleable, that's why it's used for cases. Anyone who has to push very hard to size cases is using too little case lube, especially on the lower/thicker half. A lot of common lubes work as well as branded case lubes. Anyone still using a lube pad will do as well with STP oil treatment as anything else.
Last edited by 1hole; 10-12-2015 at 04:39 PM.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |