Yes, stick with your 45-45-10.
Yes, stick with your 45-45-10.
So, I shot some on some 900fps-ish Lee 356-125-2R boolits, that I lubed with this formulation, yesterday. I got leading like nobody business. Aloy was range scrap, which is all I know about it, however I never got leading with it and straight LLA or straight JPW. This is not a criticism of the BLL, just my experience to pass on. I suspect I did not use enough or need to add more LLA to the mix. I added just a small squirt to 200 boolits, when I coated them, and sized after they dried. It looked like I got all of them coated, but it still might not have been enough. I'll add a second coat to this first batch. I did not conventionally lube them prior to tumble lubing them, since the lube groove on this boolit might as well be a micro-band anyway. >.< I'll be reading up on this thread as it gets updated.
ABQ
Krav Maga Instructor
Defensive Tactics Instructor for Public Safety Personnel
Empty Handed Gun Disarming Instructor
"If the enemy is in range, so are you." - infantry journal
" Associate with men of good quality, if you esteem your own reputation: for it is better to be alone than in bad company. " George Washington
I thought so, but the "driving bands" still felt lubed. I'll just double lube, since I have to lube before sizing. Otherwise, the bullets get hung up in the sizer after a few unlubed ones go through it and ream out any residual lube. Thanks!
Krav Maga Instructor
Defensive Tactics Instructor for Public Safety Personnel
Empty Handed Gun Disarming Instructor
"If the enemy is in range, so are you." - infantry journal
I'm still waiting for my Liquid Johnson's one step, no buff wax to arrive at the local hardware store. So I can say right up front, I haven't tried BLL yet.
But, I do have a question, since there have been two recent posts concerning Lead fouling.
my Question to Ben (or anyone):
Is it because the end resultant Lube is a liquid and has a seemingly higher concentration of solvents, that it's easier to put on a thinner layer of lube on the boolit, compared to 45-45-10, that maybe a layer that's too thin, could cause lead fouling.
~~~~~~~~~~~~~~
“If someone has a gun and is trying to kill you, it would be reasonable to shoot back with your own gun.”
― The Dalai Lama, Seattle Times, May 2001
Your question is worded in such a way as to suggest that the leading is directly related to some property of BLL. What makes you believe the leading is directly related to a failure of BLL ? ? There are so many variables involved in a leading issue in any rifle, pistol or revolver. Sizing dia., alloy, bullet style, lube, loading techniques, etc.
The leading that these 2 shooters have described could be directly related to the use of BLL. It could also be some other factor that is causing the problem?
We are MANY miles away from this situation, how can we say the leading is related to " this or that " ?
Don't overlook the 24 pages of post here about BLL . In these 470 post many ( not all ) of the shooters who have used BLL have nothing but good things to say about it.
Ben
Last edited by Ben; 03-23-2015 at 04:25 PM.
Ben, You are correct in everything you say here.
Now "the property" I'm questioning isn't necessarily a fault of BLL, it would be the fault of the person applying it.
Let me try again:
Do you suppose it's possible to put a layer of BLL on a boolit so thin, and yet cover it completely, that it could fail ?
If the answer is yes, then I am merely suggesting that, if these two incidents had too thin a layer of BLL, it could be the issue, and they could easily correct their problem by applying BLL a tiny bit heavier.
And maybe, I am WAAAYYYYY of base, and the issues with these two incidents are being caused by the myriad of other, more typical causes, that you mention.
~~~~~~~~~~~~~~
“If someone has a gun and is trying to kill you, it would be reasonable to shoot back with your own gun.”
― The Dalai Lama, Seattle Times, May 2001
Another 60 rounds of stout 44 with 300 grain boolits and two light coats if BLL on Friday. One light coat, sized and dried and then lubed lightly again. Didn't bother cleaning the bore it was spotless.
Dan
Re. Leading in 45 ACP I will be trying two more tests. 1. TL ONE MORE TIME boolits as cast. 2. Size the ones TL twice already add one more TL after sizing. Both will have 3 x TL difference will be the sizing to .452
I'm a Red Cross blood donor- are you? Make an appointment to donate today http://www.redcrossblood.org/make-donation
http://www.redcrossblood.org/
FOR Disaster Relief DONATIONS-
http://http://www.redcross.org/charitable-donations
If I'm going only BLL on pistol boolits I will tell you my "Cheat" Grab your can of Johnson's Paste wax ( Yes I know you guys have that hoarded away ala Recluse lube) Saturate a cloth with it ...preferably flannel: Lay it on your table Then take your too be sized boolits & roll them around on it then run them though your Lee sizing dies....now they are the right size so take them drop them in your bowl and add the right amount of "BLL" Swish them around ...dump... stand up let dry, load & shoot! You will love it!
" Associate with men of good quality, if you esteem your own reputation: for it is better to be alone than in bad company. " George Washington
I have the Lyman 245496 mould which is a Loverin boolit design. I have just started casting this boolit, I'm a bit leary that here is not enough bore riding surface to use BLL, 45-45-10 or similar tumble lube. Anyone with this type of experience.
Lucky Joe
"There's always a way."
Depends on the speeds you are going to be shooting the bullets at.
At 1,100 - 1,400 fps I'd say you'll be OK with BLL.
Much over 1,500 fps in the 24 bore may need about 3 of the bottom rings on your Loverin boolit filled with Ben's Red and then " over - coated " with BLL. That should take you to 2,000 fps + with good results.
Ben
Exactly that type of experience. I pan lube with Ben's Red...kake cut & dry for a day then Tumble with an overcoat of BLL
Shot it last evening with 13 gr of 2400 & ten shots into 3/4" no leading ( alloy is water quenched wheel weights sized .246") Didn't get a chance to photograph target yet!
Shot in my 1980's Tang safety 77V
" Associate with men of good quality, if you esteem your own reputation: for it is better to be alone than in bad company. " George Washington
Thanks Ben, Looking to run faster, pretty much convinced lube I will have to use a solid and then perhaps TL in BLL.
Lucky Joe
"There's always a way."
Thank you JW that is the kind of report I was hoping to hear.
Lucky Joe
"There's always a way."
I got 4 cans at Home Depot today for $6.48/can. No more on shelf. Lowes still has some. Ace hardware is out of stock, but some on the way.
Get it while it is out there fellows !
Ben
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |