Neat job, but I would have left more of an air gap at the bottom of the pot. That pot is going to transfer a lot of heat into the housing via that metal base-plate.
Neat job, but I would have left more of an air gap at the bottom of the pot. That pot is going to transfer a lot of heat into the housing via that metal base-plate.
Nice Job
Well…after trying to deal with people who….conveniently can't speaky english, trying to return a Mypin TA4 - RNR / 25a SSR package I bought on Amazon.com…….I decided to just order the Auberin SYL-2352 along with a housing and other goodies to build a PID for my LEE P4. I hope to be able to post pics in the future.
I never had to speak to anyone when I did the couple returns on amazon?
Don't like being hammered by the Cast Boolits Staff, then don't be a nail.
The rules are simple to follow.
I had a Mypin go bad within minutes of plugging it in. The supplier in China did not ask for a return or any quesitons. They shipped a replacement that arrived 3 weeks later.
Good thing too as the postage on the return would have been almost as much as the cost to purchase another with "free shipping".
Go now and pour yourself a hot one...
My bad I contacted the actual shipper from the packaging material. I don't get out much…..just when I convince the DR. I'm OK!
Last edited by echo154; 01-09-2015 at 06:45 PM. Reason: forgot part of message
Got to try the PID last weekend (Sunday) and got a fresh batch of 44Mag, 265gr boolits (Accurate 43-265F mold). Having the PID was awesome. Definitely a must have. Not only my old thermometer was off by about 40-45F (measured higher), but it was always in the way. With the PID mod, I set the temp to 750F, and casting was really easy this time, and had to flux a lot less often (probably since I never overheated the allow). Not only casting was easier, but I ended up with the lowest SD so far, at 0.3gr (average weight was about 258gr without the gas check):
This is how the loaded 44Mag round looks like with that boolit:
Will
Well my parts arrived today fellers…so I'm ready to start building….hop to have pics…Auberin unit is a little longer than the Mypin….the enclosure I bought from them is also a little on the small side too, but at least its well made and precut for the Auberin unit.
Um…..DOK say indoor lightning bad!!!! 12 v dc vs 120 v ac hmmmmm can't interchange!!!!!
I reversed the input to the SSR and POOF MY FAULT.
Did the magic smoke that makes SSRs and other elecrtronic devices work come out of it?
If so you have to get a new SSR. The magic smoke is factory installed and once the smoke leavesw the electronic component can not be fixed. Apparenty this smoke is only availble to the factories that build electronics.
Go now and pour yourself a hot one...
Finally got to test this out, as I truly wondered how hot the steel enclosure would get. I waited until the pot was about 700F, and held my hand as shown in the picture. The steel case was warm, of course, but I could comfortably leave my hand in there without problems:
I think it helps the enclosure has good venting:
Will
You all have inspired me to build my own. Parts are on the way. I will post pics once I get everything.
Also thinking about getting a pid. Does anyone have the mypin manual that frozone posted a while back. It seems he is no longer on the board. I have read through most of this thread and am looking for a simple setup for the mypin since it is 1/2 the price of the one in the op. Thanks in advance.
While I have no idea what frozone posted, or the model you are seeking.
I can guess you might be looking for a manual for Mypin TA4
https://docs.google.com/file/d/0B5ff...LTQ/edit?pli=1
=====
when I decided to built my PID, After I looked around, I went with the JLD612, as I wanted the Fahrenheit option.
http://www.lightobject.com/JLD612-Du...oller-P43.aspx
Oh, checkout this easy to read manual !
http://fhupiora.fhupiora.home.pl/JLD612Manual.pdf
Last edited by JonB_in_Glencoe; 02-21-2015 at 08:40 PM.
~~~~~~~~~~~~~~
“If someone has a gun and is trying to kill you, it would be reasonable to shoot back with your own gun.”
― The Dalai Lama, Seattle Times, May 2001
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |