As others have said, I use the Lee Magnum Melter for smelting. Does enough to keep me casting, instant setup:
http://www.amazon.com/Lee-Precision-.../dp/B00162RW52
Cheap, too.
As others have said, I use the Lee Magnum Melter for smelting. Does enough to keep me casting, instant setup:
http://www.amazon.com/Lee-Precision-.../dp/B00162RW52
Cheap, too.
Just reading this thread, I remembered that I have an antique lead casting set (1930s?) to make toy lead soldiers. The lead melter is a small dipper looking device with an electric coil included inside. For short test runs of bullets with a new mould or alloy, I'm thinking this might be the way to go. Has anyone else tried this technique?
Froggie
"It aint easy being green!"
I burned up my old hotplate yesterday, literally *smelting* on it (reducing lead oxide to metal) rather than just melting lead scrap. I should know better by now, but I had about 5 pounds of lead oxide...
The new hotplate from Walgreens gets plenty hot enough, but its thermostat cycles off and on too much so it really takes a long time.
I am thinking about digging the old one out of the trash (the heating element still works just fine) and making an open metal frame for it instead of the enclosed plastic that burned up. Have the element on all the time w/ no switch, and open sides where the air can circulate so the wires don't burn up. I can silver-solder the connections because the slip-on connectors seem to be what eventually lose springiness, get loose, overheat, and start the fire.
If that Lee magnum pot was 5 or 6 inches instead of just 4 I'd be all over it.
Froggie, no reason that shouldn't work - as long as it's only clean lead that goes in.
""start the fire""
that kinda sounds like a deal breaker to me
Yeah, that's why I'm looking for a higher-temperature connector (braze it with 40% silver) when I rebuild it on an open metal frame.
I don't think those cheap plastic hotplates were designed for running full-tilt for over an hour. I was kind of abusing it cooking the lead oxide, right after melting 20 pounds of lead w/o letting it cool down.
Like this ?
except the coil is not inside the ladle
http://www.cabelas.com/product/Hot-P...E&gclsrc=aw.ds
~~~~~~~~~~~~~~
“If someone has a gun and is trying to kill you, it would be reasonable to shoot back with your own gun.”
― The Dalai Lama, Seattle Times, May 2001
PM sent to GhostHawk for info on campfire smelting.
Sort of, but not exactly. I'll have to drag it out for my next casting session and see whether it still works. I'm thinking it will be just the thing to make a run of 25 test bullets using a new mould or a different alloy. If it actually works out, I'll try to include a picture of the ladle.
Froggie
"It aint easy being green!"
I've used a hot plate for a few years now, along with a Lyman 10 pound pot. I'm guessing I've done about 450 pounds of wheel weights and plumbing lead. I picked up a yard sale Coleman gas stove a while back, and this weekend I bought an $8 stainless 3 quart sauce pan from Walmart. It was easily twice as fast, both for scooping the dross and for melting. I can't see going back to the hot plate. Also, just for the record, I've had neighbors come over to see what the smell is when I've done large amounts (for me anyway) in the past. I get along well with them and it wasn't a problem, but if your neighbors aren't as cool as mine I can see someone complaining when the wheelweights are really dirty.
I'm getting a "bad link" message for the attachment, cdngunner. What should I be seeing"
Froggie
"It aint easy being green!"
Feedback link
http://castboolits.gunloads.com/show...ght=AlaskanGuy
Try melting them in a coffee can over a camp fire.....
Uber7mm
Bambi: The great American hunting story as told through the eyes of the antagonist.
I do as JonB - minus the handle that broke off. I do use the Academy $25 fryer & the bottle off the outdoor grill. Wife just gave me a 8 hole steel muffin tin she was throwing out. I started smelting with the sauce pan & a MAPP torch. NO, the hot plate will not work well or very long. Remove the rubber & junk before you smelt & it won't smoke much. Just tell em you got some bad meat.
Whatever!
I bought a new hot plate, like the one in your post and returned it...there is some sort of safety device that keeps shutting the electricity off just as the lead was starting to melt. This makes them useless. An old one with exposed coils might work, but these new ones don't.
Before getting a Lee electric pot (which melts just fine) I cast from an iron pot on the kitchen stove, gas or electric will get hot enough. Have a vented hood over the stove and would turn fan on high to keep any fumes/smoke out the house.
Gary
A cast iron or heavy steel pot will be fine for small batches, but electric burners are slow and will often cycle. they are best suited to mold warmers. I would just bite the boolit and get a propane burner for smelting. This one is just right for small batches, doesn't cost much, and will run off the small propane bottles or a larger one.
http://www.kitchenemporium.com/Evoo-...l#.U4fdmFIUUwo
Good luck
Shad
I believe in gold, silver, & lead, and the rights of free honest men... You can keep the "CHANGE"!
Shad
In case you guys missed it earlier in the thread, I got a Lee Magnum Melter (electric 20lb) to smelt AND cast initially. I'll get a Lee bottom pour at some point but for the time being, I'll do both in this pot. I got a Rowell #1 to ladle and I'll be using pine sawdust for flux.
If you use only 1 pot, make sure you clean it very thoroughly between every smelting and casting session. If not, you will end up with dirt and junk in your boolits.In case you guys missed it earlier in the thread, I got a Lee Magnum Melter (electric 20lb) to smelt AND cast initially. I'll get a Lee bottom pour at some point but for the time being, I'll do both in this pot. I got a Rowell #1 to ladle and I'll be using pine sawdust for flux.
Shad
I believe in gold, silver, & lead, and the rights of free honest men... You can keep the "CHANGE"!
Shad
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |