KE4GWE - - - - - - Colt 1860, it just feels right.
I add only 1-2 thou thickness as I use only ONE spray coat/bake. Trying to do what you are suggesting above is impossible. You would end up with a boolit encased in a non-controlled thickness casing that would really screw up your accuracy! And it would take an unknown number of coats/bakes which would be a total waste of time to gain a projectile that would fly uncontrollable downrange. And any know load data would be out the window.
But.......hey........go for it. That is what we do here..........bend/break the curve!!!!!!!
Let us know what you find.
banger
I have read through this post, as well as about three-fourths of the mega thread! Anyway, I didn't see much on pc affecting expansion. The reason I was wondering, I would like to use a 35 rem for hunting, and was assuming I would use a hp mold so I can get some expansion. Any idea how pc interferes, if any, with the expansion of a hp? The reason I don't go test it myself, is I have no hp mold. I am trying to figure out what route to go with my 35. I do have my HF gun and am waiting on some powder to start on my 9.
I believe you'll find reference to them a lot earlier in the original PC threads. They seem to perform acceptably, but still cost a bit more than the HF one and I'm not sure if you can use any powder or just theirs.
If you already have the HF gun why not just buy a tiny compressor used or from HF? Seems like having a really small one would be just the ticket.
Coat & shoot away................it will not bother any expansion you are anticipating. Just try smashing one on a steel plate nose to base and watch what the coating does........it expands and cracks along where the lead splits & expands..........but STILL sticks to the lead! Amazing stuff.
banger
i almost cry when a see some pictures hiere of coted bullets.I want make sombody else cry
Left is epoxy paint tumbling method,Widerlader recipe and a right (blue) powder coating..For powder coating i use simple TRIBO electrostatic gun and powder from this site www.nordicpulver.dk Hi also sels at ebey.Powder is polyester type but it works.I did go litle thin at blue bullets .
Okay.. well, I settled on a Walmart 96 cent sheet, cut in half which is almost perfect for my cheap oven, drilled, but not all the way through with a 1/2" bit.. makes a nice series of divots-- covered with the non-sticky foil. Learned that the "bottom" rack is a no-go as I started to melt again.. so I can only do about 70 at a time. I did mine face down, then about a 5 minute bake... then hit them again, and a 5 minute bake.. flip over on a flat sheet, spray once and do the full 12 min. I get PC TJ that way.. works fine...
One other comment.. a small 2-5 gal "holding tank" with a regulator could be used with the HF PC gun as well.. or a really small compressor.... for "portable" use. I was pondering those options for a while..
Balta those blue ones look great. I don't think I have seen any blue before.
A while back my big compressor crapped out on me. I'm using a little Wal-mart special...I hate it..very loud and very slow. I run it to my big tank, go inside, watch a movie then read a book then take a nap...then when everything is all pressured up I go back out and coat.
War is peace.
Freedom is slavery.
Ignorance is strength.”
― George Orwell, 1984
For some reason that blue almost looks like it's jumping out from the screen at you.
What is the best powder for coating 223 and 7.62x39? I'm using HF red and black for handgun. Will be using GCs.
I just got a 20% coupon for HF in the mail yesterday. Look slike this method will be added to the stable.
I'm headed to HF this weekend to get setup for the ESPC. TIRED OF ALL THE LEADING with the 9mm.
has anyone tried casting and then powder coating a boolit without any grease grooves at all? The reason I ask is that it would make for a shorter boolit of any given weight which means more case capacity and that often means higher mv at lower pressure.
Last edited by Balta; 11-01-2013 at 04:12 PM. Reason: gramati
Local Wed paper had 25% off hf coupon. Look what you guys made me go and do. Was 70$ fer the gun kit & all four colors. Found toaster on cl gotta get it yet.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |