Nothin much. I cut off and drilled out an old die so I could use my old Lyman Powder measure on my turret press.
Attachment 84551Attachment 84549
made myself a homemade media separator today out of an old tote 18" of bolt stock washers nuts some wood and...................a wire mess trash can!!! the size of the mess in the trash can is perfect for my corncob media i tried it without any brass but just media and the media got stuck till i tapped on the can a bit so i tossed in some freshly tumbled brass and viola the brass knocks all the media out of the can. very basic build and it only took my about ten minutes tops to complete
--ISO ITEMS--
Contender super 16 barrels
updated as of April 2023
My feedback: http://castboolits.gunloads.com/show...ight=Carbine86
^^^ I made a similar one for my SS media. I made it a little smaller so it fits in the wash tub in the garage. Works Great!
Yeah i had everything except the bolt stock laying around so i figured i would give it a try. Ive run two batches through it now without a problem. Better than spending 40 bucks on one.
--ISO ITEMS--
Contender super 16 barrels
updated as of April 2023
My feedback: http://castboolits.gunloads.com/show...ight=Carbine86
It seems to be a copy of my motorized one from 2012
http://webforum.sk/viewtopic.php?f=34&t=8337
Here's a couple pics of the case tumbler I made. Simple and compact..
Barrel Vise and Action wrench w/adapters
Primer Catcher for Rock Chucker Supreme
https://plus.google.com/photos/10573...Migl5SUlNXukgE
Enjoy........
Your Feedback is appreciated
Johnny V
NRA Benefactor
Member GOA, NAGR & Life Member OGCA
CCW OH & PA
Cap'n morgan, would you consider making me a mold... If so what would it cost
Heres some things I have made over the years to help my reloading habit. First, a set of loading blocks I made about 1960, in my Dads shop using his drill press and Fostner bits. Still use them.
Then there is the deprimer tool I made about the same time, from a 5/16" bolt with a hole in it to hold a piece of 3/32" music wire filed down to the right diameter. Outside of bolt was also filed down. Over the years it had to be cut short, repined, and finally I drilled it for a needle bearing needle from a U-Joint. Over the years I have turned the rough filing job down on the lathe also.
Next is a bullet box for cast bullets my dad made me, holds 722 45's in two layers
Heres a bullet puller I made from a piece of pipe and a bearing about 25 years ago. The pipe is rebated to hold the bearing and other end fits over the die. Includes drill, tap and allen wrench to pull case. Used it last week.
Next, a holder to hold .308/.30-06 cases while trimming, inside and outside deburring and primer pocket reaming in the lathe. Made from a piece of 1 X 2 with a 31/32 hole and a 6-32 bolt to hold it together. Made about 25 years ago, used it last week.
Next, a shell feeder for my CH Autochamp I made 3 weeks ago, screwed the colander to the block of wood and tapered a hole into the tube, works great. A copy of one I made 20 years ago.
Well, that's enough for now. I enjoy tinkering!
Steve
Very impressive. I would like to see a video of the auto bullet caster in action.
Chuck
Your Feedback is appreciated
Johnny V
NRA Benefactor
Member GOA, NAGR & Life Member OGCA
CCW OH & PA
Deleted *duplicate post*
Last edited by danomano; 12-16-2013 at 01:16 PM.
I used a section of a load bar from one of our trucks for the rack itself, and a piece of 1/8" aluminum for the backing to hang the unit.
Your Feedback is appreciated
Johnny V
NRA Benefactor
Member GOA, NAGR & Life Member OGCA
CCW OH & PA
Wow, very impressive like the mooner. Great thread
Old post on inexpensive seizer for PC or lube.
http://castboolits.gunloads.com/show...p-simple-sizer
BOB
22LR, 9MM, 45 ACP, 45 LC, 45-70, 6MM BR, 30BR, 222, 204, 22-250, 7-30 WATERS, 12GA, 36 & 44 BP
Got one of the new Rebel 17 tumblers from STM and thumbscrews are way too hard to fully tighten.
Came up with this 'wrench' made out of wood so it doesn't scratch the top of the drum.
NRA Life
USPSA L1314
SASS Life 48747
RVN/Cambodia War Games, 2nd Place
This is one of the best threads on the Net! If you made something, or modified something, PLEASE post it, not matter how trivial you think it is. There are an infinite number of ways to do something and any idea generates more ideas.
Tangentially related to reloading. My home-made Moon Clip loader:
I have some more stuff in my workshop, but its 12* out and has been snowing all day.
David
Last edited by dsbock; 01-02-2014 at 06:18 PM. Reason: Clarification
Cats are fun and magical when you can't smell their poop! Fresh Step!
JPFO; NCOWS; NRA (Life); NYSRPA (Life); SAF, SASS
I'm looking for a shooter grade Smith & Wesson Victory model in .38 Special.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |