Any body out there doing this? What are you sizing the bullet at? I am interested in using Bullseye powder, but I do have unique available.
I have a 6 cavity of this mold for plinkers for the 38 special.
If it can pull double duty.........
Any body out there doing this? What are you sizing the bullet at? I am interested in using Bullseye powder, but I do have unique available.
I have a 6 cavity of this mold for plinkers for the 38 special.
If it can pull double duty.........
Ok I have been doing some searching. I did find this.
http://castboolits.gunloads.com/showthread.php?t=96819
I did try 10 of them in my Taurus 380 auto. sized at .358 because thats what i had on hand. Ahead of 2.6 gr bullseye.
These shot well. But I thought was a little hot and I got leading.
I will have to go dig through my sizing dies. I may have a .356 sizer in with a box of stuff I got a while ago.
If not I guess a .357 LEE sizer may be in the offing.
Then I will cut the charge down to 2.2 gr and see what I get.
All 10 fed like a dream. So I am hopeful.
Slug the throat and grooves of that 380 barrel--LOTS of them run quite wide. My last 380 ACP (SIG-Sauer P-230) ran .360" throat and .359" grooves.
Since getting a 9mm Makarov about 20 years ago that DOTES on cast boolits, my 380 shooting pretty much came to an end. Generally, my experience has been with the 32 ACP, 380 ACP, and 9Mak blowbacks that once you get a handle on their barrel dimensions they can be very lead-friendly. The few recoil-operated small-bores (7.65 MAS and the Colt Government 380) REALLY bring out the best in their cartridges, and enable safer hot-rodding of the loads.
I don't paint bullets. I like Black Rifle Coffee. Sacred cows are always fair game. California is to the United States what Syria is to Russia and North Korea is to China/South Korea/Japan--a Hermit Kingdom detached from the real world and led by delusional maniacs, an economic and social basket case sustained by "foreign" aid so as to not lose military bases.
I have used a Lyman .358345 sized to .355 in an LCP. Haven't shot a lot of them but generally feed reliably. IIRC it tends to shoot a bit high but it isn't exactly a target piece anyway.
If you don't read the newspaper, you are uninformed. If you do, you are misinformed.
- Mark Twain
When a man loves cats, I am his friend and comrade without further introduction.
- Mark Twain
I use the lee 105 in my cz-83 with titegroup sized 357. It shoots good.
I originally bought that mold for 9mm but loved it in the 380. Most of the time I use the Lee 102RN mold but the 105 prints good holes on targets. I size at .358 just like I do with the 9mm and haven't had any problems in my assortment of .380 pistols. Frank
I really like that bullet, but it didn't work at all in my .380 Taurus TCP. The throat is too tight and if I tried to seat it deep enough to not jam into the rifling, it would bulge the case.
I slugged my barrel in the Taurus, and it was .358".
Yep!
3.4 gr W231 for about 938 fps out of the wifes Bersa Thunder. Sized .356" in Lee sizer. Shoots very well.
Old thread, new comment.
I'm using this boolit in my Glock 42 with good results. Mine get sized to .3565 and then loaded in front of .3 CC's of bullseye. Works very well. But my Glock 26 hates this slug, and it likes everything. Go figure.
I have been using this boolit in .380 pistols for quite a while. I compared sizing at .356 and .358 and found no significant difference in group size or pressure signs. I seat the boolit so that only a thumb-nail thickness of the top driving band is outside of the case mouth. Reliability of feeding has been perfect with powder charges recommended for the 100 grain boolit range. An old phrase that used to circulate answers your concerns - "Try it, you'll like it."
I run these as cast (unsized) and powder coated through a S&W / Walther PPK/s in front of 3.3 grains of Bullseye. Honestly, they don't group as well as Speer Gold Dots or Remington Golden Sabers, but I can keep them on a paper plate standing offhand at 25 yards with little sights and these old eyes, so they're good enough for me.
Used to shoot these all the time. I bought about 1000 bullets cast from Range Lead from a guy on this board about 15 years ago. Loaded up a box and took it to the range with me just about every other time I went shooting for a while. Worked well. I found Bullseye was my best powder. I've got some load data for it somewhere...
JDGabbard's Feedback Thread
Jdgabbard's very own boolit boxes pattern!
GOA and FPC have done more in the last decade than your NRA has done in it's entire existence... Support the ones that actually do something for you.
Very accurate in a .380 Browning 1971(1910 with target sights, longer barrel) with HP38. Killed a prairie at 180 yards with it, had a witness. Sized .357.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |