I already have a Universal M1 carbine and I would like to get the 8 shot ruger blackhawk in 30 carbine too. If you can purchase another cylinder for the 357 that would be perfect.
|
   
   
|
|
I already have a Universal M1 carbine and I would like to get the 8 shot ruger blackhawk in 30 carbine too. If you can purchase another cylinder for the 357 that would be perfect.
“The strongest reason for the people to retain the right to keep and bear arms is, as a last resort, to protect themselves against tyranny in government."
Thomas Jefferson
The only problem with socialism is that after awhile your run out of other peoples money - Margret Thatcher
Knowledge is one of the most scarce of all resources - Thomas Sowell
I'm not sure, but you might get an answer quick in the hog leg forum.
You would also need to change out the barrel for that. It wouldn't be the best idea to try to push a 358 projectile down a 30 caliber bore.
No...there is no conversion for a 30 carbine BH since it shoots a smaller bullet diameter than 357.
There is a 9mm/.357 Ruger BH convertible.
You Know You Might Be Facing your DOOM , if all you get is a click, Instead of a BOOM !
If God had wanted us to have Plastic gun stocks he would have planted plastic Trees !
short answer , no
.30 carbine has a .310 .311 ish groove dia , .357 is you guessed it .357 dia
also the .30 carbine blackhawk is a 6 shot not 8.
You might be able to pull something like that with a Dan Wesson, but not a Blackhawk. In the DW, you would need to swap out the cylinder and the barrel. I am not sure if the cylinder timing would work between the two calibers though. It would also be a very custom gun as I don't believe DW ever offered a revolver in .30 carbine.
"We the people are the rightful masters of both
Congress & the courts, not to overthrow the Constitution,
but overthrow the men who pervert the Constitution."
Abraham Lincoln
could ne be thinking of the .327 fed. ?
they didn't.
and the 30 carbine is 308, mine is anyways.
i use 313 sized boolits in it because that is what works best with the thinner 32-20 brass.
Yah, A .357 blackhawk! That'll convert most.
We need somebody/something to keep the government (cops and bureaucrats too) HONEST (by non government oversight).
Every "freedom" (latitude) given to government is a loophole in the rule of law. Every loophole in the rule of law is another hole in our freedom. When they even obey the law that is. Too often government seems to feel itself above the law.
We forgot to take out the trash in 2012, but 2016 was a charm! YESSS!
Good morning
Just get yourself a RBH 30 Carbine cylinder and barrel. Frame is the same as I understand. Or better get the whole revolver. Thay are out there if you are willing to hunt and wait.
First time I fired one was out at Ft. Hood on a pistol range. Our armorer had cases of 30 Carbine not carried on the books. Popping away at bunnies while cruising about the tank trails on an M60A1 is great sport.. even though not approved as good military conduct.
Mike in Peru
"Behold The Lamb of God that taketh away the sin of the world". John 1:29
Male Guanaco out in dry lakebed at 10,800 feet south of Arequipa.
I know guys who have shot 3220s out of them. I dont know what if anything you have to do to the gun to do this though.
Good morning
I am sitting here wondering how a 32/20 is going to fit in a 30 carbine chamber? I reload both and they are a bit different in diameter plus a 32/30 has that rim as all dash cartriges do..
Mike in peru
"Behold The Lamb of God that taketh away the sin of the world". John 1:29
Male Guanaco out in dry lakebed at 10,800 feet south of Arequipa.
Missionary -
I have a new model BH in 30 carbine. I find it very difficult to use with carbine reloaded ammo. It tends to bind on the recoil shield. I prefer the 32-20 brass. I size them with the carbine FL sizer. The only issue I've had with the 32-20 is a batch of R-P brass. About one-third would not fit in the Lee hand priming unit and many of them would bind on the recoil shield. However, this is the only time I've hand problems with the 32-20s.
On the other hand, I've had no issues using 45acp in a .45 convertible.
If you don't read the newspaper, you are uninformed. If you do, you are misinformed.
- Mark Twain
When a man loves cats, I am his friend and comrade without further introduction.
- Mark Twain
I'll sell you cylinder cheap if you can tell me how to shove a 357 bullet thought a 308 bore???
Howdy Poygan
Thank you for clarifying that. I was wondering how a 32/20 would fit into a 30 car chamber without some effort. I am going to have to study up on this ..
Mike in Peru
"Behold The Lamb of God that taketh away the sin of the world". John 1:29
Male Guanaco out in dry lakebed at 10,800 feet south of Arequipa.
Within our forum here, a well known member...Beagle did some very good work with this concept and his article written in Cast Pics/articles by members will give you all the info that you need/want. I followed his suggestions and successfully made a batch of 32-20's that work exceptionally well in my 30SBH. I load them with 32-20 dies, have no problem with OAL, get good accuracy, and no problems with clearance to recoil plate or extraction. Only a slight taper crimp is necessary to hold the bullet as the rim does the job for OAL. Bullet and powder charge are the same as for 30 Carb cases. There is nothing to speculate/worry about...it works and works well. LLS
If .30M1 is binding make sure your brass is completly free of lubricant and the chambers on the cylinder bore are dry and free of oil as well. The slight taper of the M1 brass will cause it to slide back and bind the gun if there is any lube or oil in the chambers.
Posting Permissions
| BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
| BR | Bench Rest | M | Magnum | RN | Round Nose |
| BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
| C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
| HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
| PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
| LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
| GC | Gas Check |
Reply With Quote