From my cartridge collection:
From my cartridge collection:
With a little ingenuity, cases can be made for virtually ANY gun. Before we had the wide variety of brass that's available today, I used to make 450/577 cases by turning a base and rim on a lathe, with a hole just barely big enough to press-fit a heavily annealed 30-06 case. Fireforming loss was high, but I had lots of '06 cases, and no other way to shoot the old Martini. When a case failed, I just drilled out the old '06 case and fireformed another. Worked like a charm.
Another way to go about it is to find a current case with a rim that's just a trifle TOO big to work, and trim it to fit with a lathe. Or if you're working with a rimless case, select the largest one whose base will go into the chamber. Don't worry about length: That's easily adjustable. (See below)
Then drive down to the local hobby shop and look through their selection of telescoping brass tubing. Find some tubing that will press-fit over the case you just turned to fit the chamber rim. Cut to a suitable length and press it down over the case, without trimming the old case. No glue, no soldering needed. Lube well and you can run it through a sizing die without pulling it apart. Fireform with a stiff load of Bullseye. The inner case will fireform to the tubing, and you will have a case of slightly reduced capacity, but quite usable for a decent number of reloads. There will be NO gas leakage or other undesirable problems. If you didn't KNOW you put them together, you'd almost swear they were original cases.
If you're working with a rimless case, find the largest case that will go into the chamber, and build it up with tubing that can be press-fit almost to the extractor groove, or to within half an inch of it anyhow. Cut off a suitable length and press it down over the rimless case as far as it will conveniently go (short of covering the extractor groove). Size to fit the chamber and fireform. Again, the interior case will fireform to the tubing like they were soldered, so you can make any length case you need. These will work well for numerous reloads, as long as you remember that the case does not have the capacity of an original.
Regards,
Molly
"The remedy for evil men is not the abrogation of the rights of law abiding citizens. The remedy for evil men is the gallows." Thomas Jefferson
To All,
In case anyone is wondering if it's worth your time to buy a .401WSL and/or make cases for hunting, let me tell you that one of the long-departed hunters, who was on our lease, killed over 25 WT with his 1910 & never had a deer run more than a few steps. = That 220 grain bullet @ 1800FPS is A KILLER out to 200M.
Btw, the .401 has a DISTINCTIVE report, that is like NO other rifle that I can think of. = BLAM.
(When I would hear the "BLAM" long ago when I was a "shirttail kid", in the woods, I knew we would eat venison stew soon, as Mr. Cross was deadly with his little carbine. = WWII/Korea Combat Marines tend to be excellent marksmen.)
yours, tex
Last edited by texasnative46; 07-04-2017 at 06:00 PM. Reason: typos
I recently purchased new Jamison 401WSL cases. Good quality. They shoud still be around.
cuzinbruce,
WHERE did you find the cases?
(I know someone who has a "perfectly suitable" but needs "full restoration" Model 1910 for a decent price.)
Note: To the "collectors", I won't be "messing up an antique" IF I buy the 1910, as it's been "remodeled" more than once. = For one thing, it's had an all-over cold-blue job that looks like H.
yours, tex
Last edited by texasnative46; 07-04-2017 at 05:59 PM. Reason: add
You can order cases direct from Captech Int'l. They make the (former) Jamison brand cases, and the .25-20SS and .44-77 I've bought of them are good stuff.
Also, better go to Midway and buy one of those shell catchers that hang over the ejector port. A friend had a .401, and it really flang those empties out there!
Bent Ramrod,
You are 100% CORRECT. - Not only did I see Mr. Cross shoot his .401 carbine often when I was a "shirttail kid" but he sometimes let me shoot it. - My memory is that it threw empties 20-25 feet from him/me.
Inasmuch as I sold my "1970 Colt RVN-era AR15 clone" to my landlord last Sunday, I suspect that the Model 1910 that I've mentioned here is my next "restoration" project.
yours, tex
I make 401SL from 7.62x39mm. It's the easiest & cheapest parent brass to use that I've found.
No trimming for length, no rim alteration, no extractor groove alteration.
I use 41Magnum reloading dies and LEAD 41magnum pistol bullets (.410)
I've used 35Rem in the past and it was far from as easy as sizing and trimming to length. They need the base dia turned to size after the initial forming. The 35Rem is .458/460 at the base, the .401 is .430 IIRC.
35Rem is not easy to find anymore anyway.
30-30 works OK,,just a little undersize at the base, but there's still lathe work to remove the rim and cut a new extractor groove plus trimming.
I use primarily 7.62x39 Winchester brass. Some other brands may be too thick at the mouth . I found that w/ PPU (PrviPartizan?) brass.
I've see a few long drawn out methods to expand the Soviet case from 30cal to 40cal on the net using complicated configured and shaped expander mandrils of several steps. Warnings of not trying to do the expanding in one step or brass failure is a given.
I simply took an unused RCBS 45acp expander die and removed the expander plug. I tapered that 45 plug to from just under 30cal to 40cal at the upper end.
I did it on my small lathe, but it can be done w/ files in a drill press. The plug is (was) soft and the dimensions are not critical. Being smooth and polished is most important.
The Shell Holder for the brass is a common 38sp/357. I did anneal the brass at the neck and shoulders before expanding. Simple cadence of a 1 to 5 count while rolling the case in the propane flame holding it w/ my fingers by the head and dropping it into a pan of water.
Lots of ways to anneal the brass.
I heavily lubed the inside of the necks of the dry brass and then run them into the altered expander die. That opens the mouth to .40 and leaves the rest of the case rather wasp-waist looking as the tapered expander and the tapered inner walls of the brass decide how far to a full cylinder they will be,
The case does not need trimming to length,,it is fine as is. The round headspaces on a semi-rim on the original and the 7.62x39 affords a semi-rim for headspacing also,,though a VERY small one of a only a few .000 dia over case head size. I have never has a problem with this nor seen anyone else mention any.
You can roll crimp the bullet.
Next, I run the cases into a FL 41Magnum sizer die. This forms the case up better and will deprime it if you want it to.
It'll still have the thin waist look,, that'll be with it till the first fireing when it'll disappear as it is completely fireformed.
Prime the case.
Expand the mouth and flare in the 41Mag expander.
Charge the case. I use 4227 and that is the go-to powder for the 401. I won't recommend any loads but will note that the heavier Soviet brass will NOT take the recommended charge weights that you find in print using commercial brass.
Also note that 4227 works best when a case full or very lightly compressed charge is used.
Next seat the .410d LEAD bullet using the 41MAg seater die. I lightly crimp the bullets in place for the recoil and you don't want to eject a loaded round and leave the bullet stuck in the bbl dumping powder into the action.
This last step generally leaves you with a round that looks kinda 'off',,, the taped thin waist of the yet to be fire formed case,, and sometimes the seated .410 slug will slightly bulge the mouth of the case.
The former will take care of itself very nicely when you fire them. The cases will come out of the rifle nice and cylindrical,,and about 15 ft from you
The other issue of the bulged case from the seated bullet I take care of simply by lightly lubing the outside of the case at the mouth and running the loaded round back up into the F/L sizer but just enough to size that case bulge away. It's an educated push but easily done.
Some makes of brass won't need that done, others will just because of the differences in thickness at the mouth.
The 41Mag die is a little larger at the mouth than the 401SL but this works out with the difference in brass thickness.
I do not load jacketed .410d bullets into the 401SL. Here I would only use .407/408d bullets
A Lee bullet sizer die would be the ticket for that and actually the cure for the last step in the above.
They can make one for you on order. I have a spare .400 die handy that I think I'll just lap out to .407 and make use of it.
Brass lasts for 5 or 6 loads before they become so mangled that I just scrap them. Only a couple suffered cracked necks. The Winchester really roughs them up during ejection.
But 5 reloads isn't bad for a semiauto and I'd rather replenish w/newer brass instead of trying to wring the last possible load out of them. Especially in a 100 y/old blowback op rifle.
2152aq,
THANKS for this useful post.
yours, tex
Oka, bought my second 351 1907 and now I have coming March 16th a 1910 401 winchester sl, i have dies and all the stuff for the 351, but as this is my first foray into the 401 I have bought bullets, of two different types, bought 414 super mag brass to try reform, also have reformed 7.62x39 brass coming, and am trying to buy some 6.5 grendel basic brass, I posted below about from their site, will also buy some 762x39 brass to try doing myself, looking forward to playing with it.
This brass is the same as our standard 6.5 Grendel brass except that it has not been formed and has no caliber designation on the headstamp. It should work for most 6.5 Grendel and 7.62x39mm based wildcats. This brass has not been annealed, and will require a body anneal prior to forming, and possibly a neck anneal after forming, depending on how far it is necked down. Wall thickness at the mouth of this brass is approximately .009", which is the same as our 6.5 Grendel brass prior to forming (the walls will get thicker when formed down, and the case will also get longer). Length is approximately 1.550"
Seems this would fit in an AR-15, we could call it a 401 Legend.
"Don't worry what they think. In the end it is not between them and you, it is between you and God."
Je suis Charlie!
"You won't know until you Actually try it"
"The impossible just takes longer."
"Don't let them beat you down with their inexperience."
"You'll never accomplish what you don't try. " - Moldmaker
An old thread, but the 401 is a hoot to shoot, due to ongoing eye issues and monthly treatments to keep my vision healthy I haven’t been hunting with it yet, but hope to soon.
Tried the 7.62, 414, Grendel basic brass and some Jamison and cap tech brass, all worked well.
Fun rifles.
1907 351 Winchester and 1910 401 Winchester, the most fun you can have with your clothes on.
I have one lonely .401 SL factory loaded cartridge. Is there any way I can get it to you. Can it be mailed? It has patina, but no corrosion. I'm south of Paducah, KY.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |