If you take a closer look at the price page on the accuratemolds.com website, you will see that the price for my custom molds includes sales tax where applicable, as well as shipping.
If you take a closer look at the price page on the accuratemolds.com website, you will see that the price for my custom molds includes sales tax where applicable, as well as shipping.
Considering that you get to spec the moulds as you desire these custom moulds are not pricey at all in my opinion ! Prices for Tom's work is the same as NOE, BRP, MiHec. All four give a great product at reasonable cost ! I buy from all of them and am very pleased with the results!
One of the benefits of Accurate Molds is that you can a single custom mould to your own specs in about a week or so ! You do NOT have to rely on a Group Buy !!! This alone is worth a few dollars in headache medicine or tequila ! No stress !
A 2-cavity aluminum mould is $86.00 SHIPPED !
http://www.accuratemolds.com/
Jerry
S&W .38/44 Outdoorsman Accumulator
RCBS or Lee 6 cav type, or any others that fit in a 5/16" slot..... You want they should be something else??
I cant believe my eyes!!! Is that a redesign of the old "thumper" wad cutter that molds were cut for the .38/.357??? I've always wanted one of those...
JDGabbard's Feedback Thread
Jdgabbard's very own boolit boxes pattern!
GOA and FPC have done more in the last decade than your NRA has done in it's entire existence... Support the ones that actually do something for you.
5/16" slot and single pin/screw/bolt --- that is the most common set up out there --- only a few will want something different --- suggest you politely decline such requests --- don't want to wear out the new guy who is doing great so far and make him grouchy and grumpy like MM --- (No insult intended to MM --- just he has been worn out and worn over by crazy custom requests and although I don't blame him it does make it a little harder to work with him as a cust)
Awesome mould! It reminds me of the old Modern Bond wadcutters.
~~~~~~~~~~~~~~
“If someone has a gun and is trying to kill you, it would be reasonable to shoot back with your own gun.”
― The Dalai Lama, Seattle Times, May 2001
Assuming pistol cavities (shorter than half the height of the block, such as those on GLL's pics in post #1), do you think there is enough meat on the bottom of these moulds for Erik to do a Cramer-HP conversion?
Group Buy Honcho for: 9x135 Slippery, 45x200 Target (H&G68), 45x230 Gov't Profile, 44x265 Keith
E-mail or PM me if you have one of the following commemorative Glocks you'd like to sell: FBI 100yr, Bell Helo, FOP Lodge1, Kiowa Warrior, SCI, and any new/unknown-to-me commemoratives.
All my mold blocks are 1.48" tall, and it would be easy to offer taller blocks upon request if there's sufficient demand.
Although only Erik (www.hollowpointmold.com) could say for sure I see no reason why not looking at my mold from Tom; just as much meat on the bottom if not more then a Lyman, RCBS, or Mountain mold all of which Erik has done Cramer-HP conversions for. Even if for some reason (maybe some of the longer boolit lengths) there wasn't room Erik could still probably make his new inset bar system (really nice) work since he doesn't need near as much clearance for that set-up.
I too like brass moulds. This one is from OWBM.
Blammer:
I designed mine around the Group Buy you ran ! I wanted slightly wider bands. This resulted in a slightly heavier bullet though.
Jerry
S&W .38/44 Outdoorsman Accumulator
two days ago, I finally got around to casting with the 41 WC button nose in 190 gr. Mold I got from Accurate Molds (see photo in post #15). The alloy I used was 50/50 WW/soft. They dropped easily from the mold with just a light tap and right at .412 just as I spec'd in my order to Tom...Thanks Tom.
I am Lube-sizing them right now.
Jon
~~~~~~~~~~~~~~
“If someone has a gun and is trying to kill you, it would be reasonable to shoot back with your own gun.”
― The Dalai Lama, Seattle Times, May 2001
I ordered my first mold from Tom 3 days ago, and I should have it within 2 weeks. That sure kicks the snot out of 6+ months for a group buy. Next month I will see if Tom can make a flat point version of lyman's 311465, my old single cavity mold is just too slow.
tom is real good at keeping his delivery times
you are gunna like his mold
he is becoming a habit with me
Hit em'hard
hit em'often
Just ordered another
Dave
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |