Attention! MiHec .45 200g Cramer HP 4 cavity mold

**Jared** · 01-31-2011, 08:38 PM

Thank you.

**1911sw45** · 02-01-2011, 02:34 PM

Are they done yet?????? Just kidding! But are they done yet?

Adam

**lead_her_fly** · 02-02-2011, 09:59 AM

Yeah, like today would be a good day for them to come. Of course, the mail man would have to have a snow mobile! Then again, "Neither rain, sleet or SNOW, will keep them from their appointed rounds." (I think the slogan used to go like that!)

Trapped indoors except to go run the snow blower. Gonna do some casting later in the garage. I'm with Adam on this one.

Is it here yet?

**Shakey Jakey** · 02-02-2011, 10:27 AM

Originally Posted by lead_her_fly

Yeah, like today would be a good day for them to come. Of course, the mail man would have to have a snow mobile! Then again, "Neither rain, sleet or SNOW, will keep them from their appointed rounds." (I think the slogan used to go like that!)

Trapped indoors except to go run the snow blower. Gonna do some casting later in the garage. I'm with Adam on this one.

Is it here yet?

I thought of that rain, snow, sleet thing when I got up at 6am. We've got 11 on the ground with 1-3 more to come here in Lansing.

**Tazman1602** · 02-02-2011, 11:28 AM

As far as I'm concerned MIHA should dam well take his sweet time. If I was in a hurry............well, this time of year (tax time...) heck I could use a vacation too............

Art

**Triggerhappy** · 02-02-2011, 12:17 PM

It's too cold here to snow.... almost too cold to cast...

**Maximumbob54** · 02-03-2011, 05:58 PM

It's never too cold to cast...

In Florida!

**Triggerhappy** · 02-03-2011, 06:01 PM

Yeah, I didn't have this problem in CA either. Strange.

**big dale** · 02-03-2011, 08:05 PM

Give MIHA all the time he needs to achieve perfection as usual.

Big Dale

**snuffy** · 02-04-2011, 06:25 PM

It's never too cold to cast...

Well it got UP to 16 degrees F today, I'll do some casting later. Never too cold or hot back in the loading room.

The wait now begins for the 700 grand canyon mold, hopefully this one is close on it's heels!

**Triggerhappy** · 02-04-2011, 08:50 PM

It's supposed to warm up enough to snow this weekend... Should be balmy enough to get some casting done before the Stupor Bowl...

**southpaw** · 02-05-2011, 04:07 AM

I changed my mind. I would like this in hp. I am second from the bottom. Thanks.

Jerry Jr.

**Triggerhappy** · 02-05-2011, 03:03 PM

Southpaw, you're change has been noted. Since he's already ordered pins, switching from solid to HP will be dependent on him having enough pins on order.

**JeffHolt** · 02-05-2011, 05:22 PM

Trigger,
Is it possible to get pins for a solid bullet in addition to the HP pins?

Just wonderin' how to get the most out of this mold.
Thanks,

**JeffHolt** · 02-05-2011, 05:30 PM

Trigger,
DUH! Never mind.

I forgot the part where I read you just put the pins in backwards. DOOHHH!

Jeff

**gcf** · 02-07-2011, 01:26 PM

Gents -
A fellow forum member has graciously offered to provide me sample of these bullets for evaluation.

I would like to obtain a top punch for sizing if required, & lubing w/ my RCBS LAM2.
I'm wondering if RCBS makes the correct top punch, and / or if anyone has an extra they would be willing to sell??

Any info would be greatly appreciated!

**Dale53** · 02-07-2011, 10:39 PM

gcf;
Mihec has always supplied a proper top punch (will fit either the Lyman OR the RCBS) with the moulds. I presume he'll be doing the same with this one.

Maybe the Honcho will chime in here...

FWIW
Dale53

**Calehedron** · 02-07-2011, 10:48 PM

Originally Posted by Dale53

gcf;
Mihec has always supplied a proper top punch (will fit either the Lyman OR the RCBS) with the moulds. I presume he'll be doing the same with this one.

Maybe the Honcho will chime in here...

FWIW
Dale53

Every mould I have gotten from NOE and Mihec have come with top punches for the Lyman and RCBS lubers. I keep them in their respective boxes but I dont need them in the Star.

When my mould comes in, you are welcome to the top punch.

**Triggerhappy** · 02-07-2011, 10:56 PM

Yep, Dale's right, Miha will include a top punch. However gcf just needs a top punch for some boolits he's been given. I told him I would check if I had one when I can get over there. It's possible that an RCBS top punch would work. Anyone know?

TH

**gcf** · 02-07-2011, 11:19 PM

UPDATE:

Gents -
Rumor has it that the Mihec 45 200HP, is a clone of the Lyman 452374 - but w/ a hollow point.

Question is, if it is a clone, how close is it? I found the following on Midway:

Lyman #452374 Mould
http://www.midwayusa.com/viewProduct...tNumber=204749

Lyman #374 Punch
http://www.midwayusa.com/viewProduct...tNumber=307803

Looks like the 374 punch should be close. Any thoughts?

BP	Bronze Point	IMR	Improved Military Rifle	PTD	Pointed
BR	Bench Rest	M	Magnum	RN	Round Nose
BT	Boat Tail	PL	Power-Lokt	SP	Soft Point
C	Compressed Charge	PR	Primer	SPCL	Soft Point "Core-Lokt"
HP	Hollow Point	PSPCL	Pointed Soft Point "Core Lokt"	C.O.L.	Cartridge Overall Length
PSP	Pointed Soft Point	Spz	Spitzer Point	SBT	Spitzer Boat Tail
LRN	Lead Round Nose	LWC	Lead Wad Cutter	LSWC	Lead Semi Wad Cutter
GC	Gas Check

Thread: Attention! MiHec .45 200g Cramer HP 4 cavity mold

Thread Tools

Top Punch for MiHec .45 200g Cramer HP ??

Posting Permissions